Sold the Grizzly on Craigslist for $600. Bought the Powermatic 15HH and have it up and running. Powermatic definitely is much better quality than Grizzly In my opinion. So quiet when first turned...
Type: Posts; User: dale rex; Keyword(s):
Sold the Grizzly on Craigslist for $600. Bought the Powermatic 15HH and have it up and running. Powermatic definitely is much better quality than Grizzly In my opinion. So quiet when first turned...
anyone in the PA area want to buy a used Grizzly G0454 in need of repair?;)
My 10 year old Grizzly 20" G0454 is hurting lately. Something happened in the cutterhead/pulley connection that has everything twisted and mangled. The key slot in the cutterhead and pulley is...
Im just wondering if the air pressure in the line going underground isnt enough to force any traces of condensation up and out of the vertical line in the garage itself? Maybe a drain valve...
thinking about possibly using a sump basin(18" x 24")in the ground to house some sort of drain valve at the low end right before it travels vertical into the garage. Then after entering the garage a...
just bought a pre fab 14 x 28 garage and want to run a compressed air line from my 60 gal compressor in the basement. The line will run through the basement then underground out to the garage. My...
what type of clear finish were you planning on using? If you plan to spray lacquer, you can add some red mahogany Trans-tint dye to the lacquer to get more red in the final finish. If you are...
Paul, isnt it difficult to work with the OneWay Multi-gauge when its underneath the cutterhead like that? I personally think it is better, like you mentioned in your post, to reference the knives...
Gotta either sharpen or replace the blades in my Grizzly G0454 20" planer. Im thinking about just replacing them with a better grade of steel, probably T1 from Holbren. The setting gauge that comes...
Russ, did you make those dial indicator bases or buy them somewhere?
I just bought the ETS 150/5 along witht the mini dust extractor. Around $600 for the pair. I have to say that I am so very pleased with the results that no other sander that I have owner so far has...
Im gonna replace the stock blades in my Grizzly G0454 with a set of T1 blades form Holbren soon. Never had them out yet, so I was wondering what the best method is to set such large 20" blades...
I am considering doing the same for my Grizzly 8" jointer and 20" planer sometime in the future. FYI I recently saw that Grizzly is selling the Byrd head for the 20" planers for $850, reduced from...
guess i should have clarified that...........I want the helical head with the carbide cutters. I realize that Grizzly has spiral head with steel blades that follow a spiral pattern accross the...
any hints tips or suggestions? probably leaning more towards the Grizzly model because of the cost. Gonna install it myself,.... any special tools needed?
I get my 5 minute epoxy from Woodcraft.......in 8 ounce bottles. Its far superior (IMHO) to the cheap Borg stuff in the little injector mixers.
I use alot of System Three 5 minute epoxy. Its great for small repairs and glue-ups that require a fast dry, or for exterior glue joints. I sometimes use T-88 for a slower setting glue.........never...
why not buy a Delta Unisaw from Woodcraft? I think they still have them there. I bought mine a few years ago from Woodcraft and am extremely happy with it.
I have a couple rocking chairs that I need to repair. They both have loose rungs and legs. I saw Chair Doctor advertised on Woodcraft and wondered if anyone has any experience with it? Does it...
I have a PC 333vs that I recently bought when my old Bosch 3283 started having problems. I dont like the PC sander in comparison to my old Bosch. The PC stops spinning when I put too much downward...
i remember Dizzy coming here and other woodworking forums. I wondered what happened to him...........dont see him anymore.
if you dont mind a longer drive, check out Bailey Wood Products in Kempton, PA. Family owned, very reasonable prices. Check it out at www.baileywp.com
cool.........now a field trip to Tractor Supply is in order. Thats where I bought my compressor. I find myself going there more and more.:D Much better than the BORGs IMHO.
need a hose to connect my new stationary compressor to a piping system that I am getting ready to install. Was going to buy some bulk air hose at first, and simply put barbed fittings and hose clamps...
Dave.......I have that same heater for my shop and its works great! I cant believe how fast it heats my 750 sq ft basement shop from 45 degrees to 70 degrees. You will be happy with it, especially...