Search:

Type: Posts; User: Ryan Brucks; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    2,217

    and the MDF was perfectly flat. i used killz...

    and the MDF was perfectly flat.

    i used killz oil primer and waited about 2 days to sand. I even turned the desk at an angle to the light so I could sand out the smallest little dimples... thats...
  2. Replies
    4
    Views
    2,217

    I think my problem was touching it too much with...

    I think my problem was touching it too much with the brush while it was drying.

    my problem was the front edges of the desk were running pretty bad (despite the no drips label) and I had to keep...
  3. Replies
    4
    Views
    2,217

    computer desk glossy fail.... what next?

    Hey guys,

    I made myself a new L shaped computer desk last week. The top is made from two separate sheets of 2'x4' MDF. Desk has crisp chamfered edges. I wanted this to come out with a hi-glossy...
  4. As a CV owner, I can certainly understand some...

    As a CV owner, I can certainly understand some people wanting steel. Especially after my experience with the CV shipping. I received 2 completely busted cyclone bodies before the 3rd one arrived OK....
  5. Also consider weather it is attached to a house...

    Also consider weather it is attached to a house or not.

    With your 1st plan, you are putting the garage under positive pressure. Now when you open the garage door to the house, much more dusty air...
  6. Replies
    12
    Views
    2,051

    just remember that if you ran it without a...

    just remember that if you ran it without a collection bin, or worse without filters hooked up, the thing will be WAY louder. I was worried too when I first tested my unit out but after getting...
  7. These are probably the same old curves that had...

    These are probably the same old curves that had problems. I asked James Bushey about them and he said they were done before the Busheys were involved....back under Ed Morgana (probably said that...
  8. Replies
    36
    Views
    11,943

    this might not apply to you but here goes. I...

    this might not apply to you but here goes.

    I had a bunch of extra melamine shelving available since I changed my plans and ended up not having enough space for them.

    I used the extra melamine...
  9. just FYI that Clearvue indeed published fan...

    just FYI that Clearvue indeed published fan curves for the 1800 and Max a few months ago.

    http://www.clearvuecyclones.com/Bullentin/attachment.php?attachmentid=463&d=1337614552

    of course we...
  10. Replies
    37
    Views
    6,701

    some pics of my blade guard. has pieces to...

    some pics of my blade guard. has pieces to surround the riving knife which keeps the guard safely away from the blade should it get bumped. Also reduced the volume of the guard some.
    ...
  11. Replies
    37
    Views
    6,701

    Interesting note on the linked thread for people...

    Interesting note on the linked thread for people making their own guard.

    Someone mentioned the position of the dust port on the gaurd in relation to the blade could matter. if the port is directly...
  12. i've compared my 16in clearvue impeller running...

    i've compared my 16in clearvue impeller running through a 2.5" line to my 5hp "peak" rigid shopvac... they were really close, would need testing to be able to tell the difference for sure, but I...
  13. Replies
    75
    Views
    22,650

    Very interesting thread, especially as someone...

    Very interesting thread, especially as someone who has only minimally used his shaper. Since my shaper is part of a combination machine, I don't see myself using it for most jointing operations, but...
  14. Replies
    37
    Views
    6,701

    can the excalibur not be set to ride up higher or...

    can the excalibur not be set to ride up higher or anything? does it have an ability to fix the height at a certain level, or does it always have to be lifting up by the piece?

    I ask since raising...
  15. Replies
    37
    Views
    6,701

    Sorry to hear about your injury but thanks for...

    Sorry to hear about your injury but thanks for posting this. I was confused about why you thought the guard itself bumped the offcut... doesn't the excalubur ride above the workpiece??

    The...
  16. I understand the 3 phase and the VFD. I have that...

    I understand the 3 phase and the VFD. I have that same setup myself.

    What I meant was that, almost all motors in this size class are meant to run at 3450rpm.

    So either they are using a motor...
  17. One thing has always puzzled me about the 5hp...

    One thing has always puzzled me about the 5hp smart oneida. If it increases RPMs to get better suction at higher SP, that means it must have some RPMs to add....

    meaning either their motors are...
  18. thanks Tony, cleared it up nicely for me. for...

    thanks Tony, cleared it up nicely for me. for some reason google was hard to get help from there.
  19. silly question... cope&pattern vs rail&stile... same thing?

    Hey guys,

    I am likely getting a moulder head from WMooreprofiles and some custom knives.

    I'd also like to get some knives for making traditional cabinet doors. I was just a bit confused by...
  20. missed your post as well William. Thanks. I guess...

    missed your post as well William. Thanks. I guess give those guys a call over at WMoore Profiles.
  21. oops, guess I will look around at other moulding...

    oops, guess I will look around at other moulding heads. The grizzly only comes in 1" and 3/4" as far as I could tell.
  22. thanks for the tips. cant believe I didn't notice...

    thanks for the tips. cant believe I didn't notice those corners are mitered....

    looks like I can get the grizzly moulder head and profiles for the cheapest. around 100 bucks with the head and...
  23. Could someone help me find a cutter, similiar to the doors of this desk?

    Hey Guys,

    I'm just a hobbyist woodworker who's made a few things around the house... but now I am getting requests for inlaws and extended family to make things.


    Mother in law just asked if I...
  24. here's a thread where I got the dimensions to...

    here's a thread where I got the dimensions to make mine for the harbor freight. super easy with a jigsaw then a minute with the ROS to clean up the edges if necessary.
    ...
  25. not a bad idea. I was too young to understand...

    not a bad idea.

    I was too young to understand at the time but it was pretty scary for my parents... at first they fed him cookies through a small gap in the garage door in hopes of keeping him...
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4