Search:

Type: Posts; User: Dan Barber; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    31
    Views
    3,323

    I honestly think that might be an AI created...

    I honestly think that might be an AI created picture. It's scary what can be done these days.
  2. Replies
    16
    Views
    1,750

    Source for Milwaukee 8mm collet:...

    Source for Milwaukee 8mm collet: https://www.sparepartsworld.co.uk/product/4931479477

    I bet the collet works in the US market router as well. It would not make sense to have a different rotor and...
  3. Replies
    11
    Views
    927

    Every number in the photo is from the motor, they...

    Every number in the photo is from the motor, they have nothing to do with the jointer model number.

    For instance if you search for Magnetek B674, it will return several electric motor offerings.
    ...
  4. A simple limit switch wired in series with the...

    A simple limit switch wired in series with the light would do that trick.
  5. Replies
    12
    Views
    1,389

    Negative to cleaning grill grates with anything...

    Negative to cleaning grill grates with anything the resembles a wire brush. Too many opportunities to ingest a stray wire. Much better products available today to not need a brush anywhere near a...
  6. Replies
    9
    Views
    893

    Richard, thanks for that info, I've never seen...

    Richard, thanks for that info, I've never seen one of those before. It looks like Pro-Grip actually calls that a Twin Clamp, the Back to Back is slightly different. I can certainly see a use case for...
  7. Replies
    9
    Views
    893

    Are you certain that is not two clamps that are...

    Are you certain that is not two clamps that are stuck together with double sided tape or some sort adhesive.
  8. Replies
    8
    Views
    626

    Agree with Mike, look for the wiring diagram...

    Agree with Mike, look for the wiring diagram inside the machine. Also, the part you have in the pictures is called a contactor, not a switch.
  9. Sounds like a good excuse to get track saw Brian...

    Sounds like a good excuse to get track saw Brian ;)
  10. I've been following that channel for a while....

    I've been following that channel for a while. Truly a talented craftsman!
  11. Replies
    32
    Views
    2,970

    Good ending and good on you for doing the right...

    Good ending and good on you for doing the right thing. Many these days would not.
  12. Replies
    3,513
    Views
    881,297

    Sticky: I grew up just over the hill (the Tug Hill...

    I grew up just over the hill (the Tug Hill Plateau) from Oswego, I have family in that area still. I grew up just North of Boonville NY, the last year I lived there was 1976, Boonville received 346...
  13. You must be pretty good to make 16" crosscuts...

    You must be pretty good to make 16" crosscuts with a sledge :D
  14. Thread: Red squares

    by Dan Barber
    Replies
    26
    Views
    2,142

    Have you ever looked at a Woodpecker square's...

    Have you ever looked at a Woodpecker square's accuracy? They are very much as square as a machinist square but without a certificate (that's not important to me, I know what's square and what's not)....
  15. Thread: Red squares

    by Dan Barber
    Replies
    26
    Views
    2,142

    Yes, they are perfect to use with your track saw.

    Yes, they are perfect to use with your track saw.
  16. Replies
    54
    Views
    6,826

    A very experienced table saw operator MIGHT get...

    A very experienced table saw operator MIGHT get away with this operation, but it's not the thing to be showing the typical begging woodworker which would be Woodworkers Journal prime audience. That...
  17. Replies
    8
    Views
    2,701

    I would design to the actual dimensions of my...

    I would design to the actual dimensions of my working stock. Too much chance for accumulated error(s) using the nominal size. I would also design in mm, much easier than constantly converting back...
  18. Replies
    21
    Views
    1,839

    Those bases would be much more useful if they...

    Those bases would be much more useful if they were round in my opinion. Being oval, they would not be practical to use with an edge guide.
  19. Replies
    34
    Views
    7,200

    That voltage is for the individual cells in the...

    That voltage is for the individual cells in the Tesla battery pack. The entire pack output is more like 400 volts. Adapting a BEV battery pack to an old battery forklift would be a VERY challenging...
  20. That's a fascinating bit of trivia!

    That's a fascinating bit of trivia!
  21. Replies
    27
    Views
    1,756

    I'm thankful that I'm grandfathered in as long as...

    I'm thankful that I'm grandfathered in as long as I maintain my subscription at $300 per year. I have the full functionality and really like the post processor for the CNC mill. The whole package has...
  22. Replies
    27
    Views
    1,756

    You guys are aware that Fusion 360 is free for...

    You guys are aware that Fusion 360 is free for hobbyists - correct?

    https://www.autodesk.com/products/fusion-360/personal
  23. Replies
    26
    Views
    1,475

    You guys are such enablers. Guess what's in my...

    You guys are such enablers. Guess what's in my shopping cart right now?
  24. Replies
    42
    Views
    2,527

    The better track saws are inherently safer as...

    The better track saws are inherently safer as well, the blade is completely enclosed other than whets below the work surface, it has a riving knife and anti-kickback built into the track interface. I...
  25. Replies
    42
    Views
    2,527

    Well, you have a saw. Making a shorter Kreg track...

    Well, you have a saw. Making a shorter Kreg track doesn't sound too hard.
Results 1 to 25 of 218
Page 1 of 9 1 2 3 4