Search:

Type: Posts; User: Roger Rayburn; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. I use a version of this one ...

    I use a version of this one
    http://www.amazon.com/POWERTEC-70130-Collection-Fittings-Reducer/dp/B00LPOUW2Q/ref=sr_1_21?ie=UTF8&qid=1447893349&sr=8-21&keywords=vac+hose
    but I bought it at...
  2. Guy on LumberJocks built one. See thread 95246.

    Guy on LumberJocks built one. See thread 95246.
  3. Stumpy Nubs did this as an exercise / experiment....

    Stumpy Nubs did this as an exercise / experiment. Go to his site and watch the video. It's worth it.
  4. Replies
    4
    Views
    2,300

    On so many levels he Craftsman unit is superior...

    On so many levels he Craftsman unit is superior to the IVAC / I-socket. AND it was less expensive. If I could find a couple more I'd buy them myself. That controller was one of the few things...
  5. Your wobble description suggests to me that your...

    Your wobble description suggests to me that your dowel holes are perhaps a tiny bit too shallow, as Mark suggests, and therefore it is impossible to completely seat the edges to each other. This is...
  6. Replies
    4
    Views
    3,192

    Put the slab in a big garbage bag, seal it up and...

    Put the slab in a big garbage bag, seal it up and put it in the sun (preferably on a concrete slab to add some solar reflection) for a couple weeks to fry the buggers. You don't want any of them...
  7. Replies
    13
    Views
    2,266

    If I had to do it but only needed a few, I'd...

    If I had to do it but only needed a few, I'd tackle it with rasps, files and sandpaper. You could probably knock out a half dozen in the time it would date to figure out a different method. Those...
  8. Congratulations! Well done. This was the hard...

    Congratulations! Well done. This was the hard part. You should go buy yourself a new tool as a reward. I'm serious, you earned it.
  9. Replies
    21
    Views
    4,677

    I'm in the camp of mapping out the circuits. If...

    I'm in the camp of mapping out the circuits. If you don't have a helper, pick up a Circuit Detective from Harbor Freight, for example, it will help you identify what is where. Importantly, test...
  10. Replies
    14
    Views
    2,590

    I definitely agree with the brick clips. I had...

    I definitely agree with the brick clips. I had some for several years and used them to hang signs and wreaths on the outside of the house and to hang some things on the fireplace inside. I passed...
  11. Replies
    11
    Views
    1,703

    Don't confuse "suction" with volume. I have an...

    Don't confuse "suction" with volume. I have an HF unit, I'm running 20 feet or so of 4" HVAC duct over to a planer with stops along the way at a Table Saw, sander, etc. I have blast gates, as it...
  12. Replies
    9
    Views
    2,661

    I bought an HTC mobile base for my Griz table saw...

    I bought an HTC mobile base for my Griz table saw when I got it. I was really happy with it so bought an adjustable base for my Buffalo Forge drill press. It has served me well and I have no...
  13. Replies
    8
    Views
    2,859

    I agree with Alan. A bead down the bottom of he...

    I agree with Alan. A bead down the bottom of he groove will force some squeeze out into the sides of the groove when you clamp it closed. If you have a good fit that then swells a bit, good clamps...
  14. I experienced the nut tightening until I included...

    I experienced the nut tightening until I included a washer below the nut. It's a different washer from the ones for the spindles because the shaft has to pass through the washer but it is a smaller...
  15. Amazon still has a few in stock ...

    Amazon still has a few in stock http://www.amazon.com/Ridgid-EB4424-Sander-Oscillating-Edge/dp/B0015B9G0S/ref=sr_1_1?ie=UTF8&qid=1382846032&sr=8-1&keywords=eb4424
  16. I want to thank everyone for their analysis and...

    I want to thank everyone for their analysis and their comments. It is absolutely everything I hoped for to have people who actually understand this stuff discuss it and arrive at data and...
  17. Better off with swivel (adjustable) elbows or with flexible duct on 4 inch turns?

    I'm getting ready to move to a 4 inch piped (sheet metal snap lock) duct system with drops to replace my single duct moved machine to machine approach. Contemplating it, I have some challenges that...
  18. I've had very good luck with these. ...

    I've had very good luck with these. http://www.homedepot.com/p/E-Z-Ancor-Twist-N-Lock-50-Drywall-Anchors-with-Screws-25-Pack-25200/100133106#.UbLFwh7nbIU They aren't expensive and they are...
  19. Replies
    23
    Views
    4,841

    My garage has an 11 foot ceiling. I built a rack...

    My garage has an 11 foot ceiling. I built a rack that looks like a ladderer except the rungs are 2 foot long 1 1/4 inch dowels and they are only spaced about 6 inches apart. I hung it from the...
  20. Replies
    6
    Views
    2,065

    I personally like the ones Myk Rian shows the pic...

    I personally like the ones Myk Rian shows the pic of. The real advantage for me is that they don't require high precision for initial positioning of the clamp "legs", and then they give me lots of...
  21. I have a cheap dust collector but I upgraded the...

    I have a cheap dust collector but I upgraded the filter bag to an American Filter from Highland Woodworking that filters to 1 micron. Others go with a Wynn filter cartridge. I hang my Jet air...
  22. Have not heard of it, what is it? Do you have a ...

    Have not heard of it, what is it? Do you have a link?
  23. Martha Stewart just called to tell me she hates...

    Martha Stewart just called to tell me she hates you.
  24. Replies
    30
    Views
    8,071

    I started with the PC 890. I liked it and had...

    I started with the PC 890. I liked it and had all the flexibility I needed. I liked the above the table height changes and the above the table bit changes. But, I knew someday I'd want more...
  25. Replies
    18
    Views
    17,282

    I am having a difficult time comprehending the...

    I am having a difficult time comprehending the idea of reversing the motor rotation. It seems to me that reversing the rotation is counter productive unless you also reverse the "directionality" of...
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4