Search:

Type: Posts; User: Bob Johnson2; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    19
    Views
    2,844

    Are there beveled edges on the stall matts? if...

    Are there beveled edges on the stall matts? if not, does the edge cause a trip issue?
  2. Replies
    19
    Views
    2,844

    Thanks Ron, for $8 I'll give it a shot.

    Thanks Ron, for $8 I'll give it a shot.
  3. Replies
    19
    Views
    2,844

    Need Anti-Fatigue mat recommendations

    I'm having issues with arthritis in my toe joints, seems to get exasperated on the days I spend hours in the shop. Would like to try a few mats, 3 around the workbench and 1 in front of the TS. I do...
  4. Replies
    10
    Views
    1,026

    Thanks folks, it gives me a couple solutions I...

    Thanks folks, it gives me a couple solutions I can work with.
  5. Replies
    10
    Views
    1,026

    Inset door hinges

    Looking for a bit of help building the buffet pictured below.


    I've never built anything where the legs stand proud of the cabinet doors, does anyone know of a hinge that would provide more then...
  6. Thread: Iron coin

    by Bob Johnson2
    Replies
    14
    Views
    1,540

    I've used washers but knockouts from electrical...

    I've used washers but knockouts from electrical boxes might work.
  7. Replies
    13
    Views
    1,088

    You could look at ash too.

    You could look at ash too.
  8. Replies
    6
    Views
    981

    Have you ever tried RV Parky?, it shows a few...

    Have you ever tried RV Parky?, it shows a few more or less close by. If it were me I'd try Johnson County Park http://www.jocoparks.com/johnson-county-park/ as I like public parks. There is a Lake...
  9. Replies
    6
    Views
    946

    Here's another that I've been sitting on, no pun...

    Here's another that I've been sitting on, no pun intended. https://www.jakeschair.com/
  10. Replies
    33
    Views
    3,504

    I picked up these over the summer....

    I picked up these over the summer. https://smile.amazon.com/gp/product/B007JZCVAQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
  11. Replies
    8
    Views
    987

    While I agree with the others as to not seeing a...

    While I agree with the others as to not seeing a reason to keep adjusting it, I don't remember the last time I've changed mine, and I change blades a lot. I do see a knob with 2" threaded 5/16"-18...
  12. Replies
    8
    Views
    1,391

    If you can't fit a contractors saw on a mobile...

    If you can't fit a contractors saw on a mobile base then a jobsite saw may be your only other choice. When looking at the $800 price you are factoring in the $200 dado set which you'll have to buy no...
  13. Replies
    15
    Views
    1,532

    The link in the 2nd post works. At least it does...

    The link in the 2nd post works. At least it does from Chrome.
  14. Replies
    7
    Views
    2,251

    I'd also turn the TS around as the door is on the...

    I'd also turn the TS around as the door is on the outfeed side at the moment. I'd also check tool heights for clearance of longer and wider boards.
  15. Replies
    19
    Views
    1,666

    From the pic the Ultimate Table Saw Sled looks to...

    From the pic the Ultimate Table Saw Sled looks to use an awful lot of cut depth.

    I use the MG unless the material doesn't fit between it and the blade, as in wider panels, and also for anything...
  16. Replies
    15
    Views
    1,532

    Don't know about iut being the best, but...

    Don't know about iut being the best, but https://cutlistoptimizer.com/ is free and it works.
  17. Replies
    14
    Views
    3,356

    I looked on line at the WB'ed, looks like most...

    I looked on line at the WB'ed, looks like most folks don't care for it, have you used it?
  18. Replies
    14
    Views
    3,356

    Winter use of Contact Cement

    Looking at the contact cement instructions it says the application temp range is 64F - 77F degrees, for safety you are supposed to keep the doors and windows open.

    I have a few items to cover with...
  19. Replies
    39
    Views
    3,719

    FWIW... I've been putting in some time with my...

    FWIW... I've been putting in some time with my Dewalt, something that just came up is when running a thin kerf blade the blade moves during the cut. Did a few cross cuts and I can see the blade move...
  20. Replies
    19
    Views
    2,487

    Google "clamp rack". Each slot has just 1 bar...

    Google "clamp rack". Each slot has just 1 bar clamp on mine although some hold more. I have 2 racks of 16ish.
  21. Replies
    30
    Views
    3,552

    Hanging on a nail next to the entry door to the...

    Hanging on a nail next to the entry door to the shop I have roughly a dozen steel rulers, 12", 14", and 24", I also have 6 6 inchers that reside either in the apron or supposedly on a small table by...
  22. I've got a set, from many moons ago. The coarse...

    I've got a set, from many moons ago. The coarse wheel is like a grinding wheel, works okay on something like a hatchet, the fine is pretty good to put a finished edge on knives and such although they...
  23. Replies
    39
    Views
    3,719

    About 2 months ago I went from a 3 hp Unisaw to a...

    About 2 months ago I went from a 3 hp Unisaw to a Dewalt dwe7491rs jobsite saw. I obviously don't have a lot of time with the Dewalt but here's my thoughts so far.

    Added wing and an outfeed table,...
  24. Replies
    21
    Views
    3,883

    I've got a Dadonator, cuts well but the finish,...

    I've got a Dadonator, cuts well but the finish, or lack of, on the blades themselves is lacking. Need to keep them waxed or they corrode. This may have changed, my set is about 20 years old.
  25. Replies
    18
    Views
    1,640

    Left, right. Cause it just works that way.

    Left, right. Cause it just works that way.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4