Search:

Type: Posts; User: Ernie DeMartino; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Please count me in Thank you

    Please count me in
    Thank you
  2. Please count me in Thank you

    Please count me in
    Thank you
  3. Please count me in Thank you

    Please count me in
    Thank you
  4. Please count me in Thank you

    Please count me in
    Thank you
  5. Please count me in Thank you

    Please count me in
    Thank you
  6. Please count me in Thank you

    Please count me in
    Thank you
  7. Please count me in Thank you

    Please count me in
    Thank you
  8. Please count me in. Thanks!

    Please count me in. Thanks!
  9. Please count me in. Thanks!

    Please count me in. Thanks!
  10. Count me in as well, either is fine. Thank you

    Count me in as well, either is fine. Thank you
  11. Replies
    2
    Views
    3,214

    I would try EPS , always seems to work for me.

    I would try EPS , always seems to work for me.
  12. Replies
    11
    Views
    1,756

    How about using MDF, its cheap

    How about using MDF, its cheap
  13. Replies
    6
    Views
    1,183

    Thanks Alexa and Rodne. I found a connection off...

    Thanks Alexa and Rodne. I found a connection off of the MPC that was loose. On my initial check I didn't see it until I removed the termination and the wire came out of the crimp. So far so good,...
  14. Replies
    6
    Views
    1,183

    Walt, its a DSP, MPC6515. I think I need to...

    Walt,
    its a DSP, MPC6515. I think I need to replace. Not sure why I thought the PS was the issue.
    Thanks
    Ernie
  15. Replies
    6
    Views
    1,183

    Laser Power Issues

    While I was engraving earlier today, I noticed the laser continued to fire when I paused the machine. I had to turn the laser power off to get it to stop. I rebooted, tried again, this time I was...
  16. Please Count me in. Thank you

    Please Count me in.
    Thank you
  17. Replies
    43
    Views
    24,646

    Please count me in. Thank you

    Please count me in.
    Thank you
  18. Replies
    4
    Views
    1,678

    The project is indoors; basically Im mounting a...

    The project is indoors; basically Im mounting a hardwood plaque to the osb board. I plan on using oil based poly unless there is a better alternative.
    Thank you
  19. Replies
    4
    Views
    1,678

    OSB Board

    I am working on a customer project that requires a clear coat finish applied to OSB board. Im planning on using poly but I'm fairly sure the OSB will soak it up.
    I'm wondering if I should apply a...
  20. Please count me in as well. Thank you.

    Please count me in as well.

    Thank you.
  21. We've had good luck with the agate slices from...

    We've had good luck with the agate slices from LaserSketch.
  22. I had the same issue when my stinger arrived....

    I had the same issue when my stinger arrived. Flatbed is the way to go. I got a price to rent a forklift- 500$ for the day, ended up using the flatbed only cost 100.
    Good luck your going to have a...
  23. Replies
    3
    Views
    1,173

    John, I agree with you; should have pointed that...

    John, I agree with you; should have pointed that out first.
  24. Replies
    3
    Views
    1,173

    My guess is that the file is corrupted; I had a...

    My guess is that the file is corrupted; I had a similar issue with a corel file a while back. I copied the design into a new CDR file and the file ran as expected. Hopefully this helps.

    Ernie
  25. Replies
    5
    Views
    1,514

    Here you go..

    Let me know if you are unable to open.

    Ernie
Results 1 to 25 of 57
Page 1 of 3 1 2 3