Search:

Type: Posts; User: Dennis Yamamoto; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    1,611

    Three other 3-phase machines are running fine, so...

    Three other 3-phase machines are running fine, so it is not the Phase Perfect.
    I did, however, replace the capacitors a few years back.

    Thanks
  2. Replies
    20
    Views
    1,611

    I understand that the breaker should be able to...

    I understand that the breaker should be able to pass its full rated current unless tripped by an overload. I was wondering if a failing breaker could be ON but not pass its rated current. Probably...
  3. I have purchased several Lenox resaw blades...

    I have purchased several Lenox resaw blades including a Woodmaster CT 1.3 TPI from Industrial Blade in Santa Ana. The Woodmaster is either 27 or 54mm wide.
  4. Replies
    20
    Views
    1,611

    I removed the jumpers for delta configuration and...

    I removed the jumpers for delta configuration and checked the resistance at the six terminals:
    0.4 ohms between U1 and U2, V1 and V2, W1 and W2.
    infinite between each of the above windings or...
  5. Replies
    20
    Views
    1,611

    When I first got the bandsaw, the belts were old...

    When I first got the bandsaw, the belts were old and slipping so I replaced them. I don't think they are slipping now. I suppose I could stop the blade or the lower wheel and see if the pulley is...
  6. Replies
    20
    Views
    1,611

    source for IEC metric 3 phase motor

    I have a Minimax Centauro S600P/MM24 that I bought used. I can easily stop the motor resawing 6-10" hardwood. I presume the previous owner overheated the motor windings.

    The original motor is...
  7. Hi Joe, The Krenov School uses a Lenox...

    Hi Joe,

    The Krenov School uses a Lenox Woodmaster CT 1.3 TPI 1" blade for resawing on their Agazzani bandsaw. Bigger gullets in the 1.3 TPI blade allow for more sawdust for a tall resaw. I have...
  8. Hi Josh, A number of folks on the Felder...

    Hi Josh,

    A number of folks on the Felder Owners Group use Tenryu blades.
    I use the following combination blade on my CF741 most of the time. If I'm ripping 8/4+ material that is really hard, I...
  9. Replies
    20
    Views
    2,448

    Another thought: it's approximately 5/16". Given...

    Another thought: it's approximately 5/16". Given your drawer box opening and drawer side thickness, use Blum's instructions to calculate the drawer box width which will give you the side recess. If...
  10. Replies
    20
    Views
    2,448

    I believe that Blum tandem 563H's require about a...

    I believe that Blum tandem 563H's require about a 5/16" side recess. So, if you want to do half blind dovetails in front for an inset drawer, you will have to account for this. I did this by using...
  11. Replies
    21
    Views
    3,086

    I use what the Krenov School used a few years...

    I use what the Krenov School used a few years ago: Intertape 591. It does take some effort to remove, but you don't want it to come off when you are template routing or shaping. It's the only thing...
  12. Replies
    5
    Views
    955

    The Blum boring jig does work with Movento's. I...

    The Blum boring jig does work with Movento's. I just used the jig on both Movento 763H and 769 slides.
  13. Replies
    5
    Views
    955

    Both left and right sides provide a rear tilt...

    Both left and right sides provide a rear tilt adjustment to tilt the front of the drawer forward. It looks like the one on the left is raised higher. Rotate the grey tabs to adjust the tilt.

    The...
  14. Replies
    44
    Views
    5,676

    I got this suggestion from Jamie in the Bay Area...

    I got this suggestion from Jamie in the Bay Area Woodworking Assoc: you can gang cut all of the half-laps by stretch wrapping all of the grid boards together that are the same length. In addition,...
  15. I like Industrial Blade and Products, Santa Ana,...

    I like Industrial Blade and Products, Santa Ana, CA for Lenox. Excellent prices, service and a nice weld.

    Dennis
  16. Replies
    11
    Views
    2,236

    Did it work before? Besides turning on the...

    Did it work before?

    Besides turning on the main power switch, the emergency stop buttons have to be disengaged. That is, turn them so they pop out. Also there are several safety switches. For...
  17. Replies
    14
    Views
    3,171

    Double bevel marquetry

    Double bevel marquetry
  18. Replies
    32
    Views
    4,704

    A couple of people suggested using a Krenov...

    A couple of people suggested using a Krenov coopering plane. Here's a picture of my Krenov coopering plane where I'm planing the concave side of a coopered door. It's some effort to shape the sole...
  19. See Charlie's page:...

    See Charlie's page:
    http://www.solowoodworker.com/mm/switch.html

    I have a 2005 MM16 and I'm on my 3rd switch
  20. Replies
    122
    Views
    27,626

    See John White's book, " Care and Repair of Shop...

    See John White's book, " Care and Repair of Shop Machines". In Chapter 2 on Jointers, he shows how to make a master bar for checking jointer tables. It's as economical as MDF and drywall screws.
  21. Replies
    19
    Views
    3,864

    I believe a 16" HD Northfield jointer weighs...

    I believe a 16" HD Northfield jointer weighs about 2000 pounds. I would guess that any mobile base would settle to however flat your concrete floor is. You could loosen the bolt and nut on the...
  22. I got the DeWalt. It worked great for the knife...

    I got the DeWalt. It worked great for the knife hinges! I can see why so many folks recommend these small routers and especially the Dewalt.

    Thanks everyone!

    Dennis
  23. Thanks everyone! Looks like the Dewalt unless I...

    Thanks everyone! Looks like the Dewalt unless I want something smaller like the Ridgid.

    Mike,

    Thanks for your suggestion for routing close to the line, and finishing with a chisel. I have a...
  24. looking for recommendation - trim router for routing small mortises

    I need to route mortises for some small brass knife hinges. For routing these small mortises, what trim router would you buy today, and why? For me it seems like good depth adjustment, and having...
  25. Replies
    22
    Views
    4,713

    I don't like Felder's eccentric clamps. I find...

    I don't like Felder's eccentric clamps. I find them difficult to set up just right. What some people do is to use a wood spacer. They put the spacer under the clamp head to set the clamp height,...
Results 1 to 25 of 111
Page 1 of 5 1 2 3 4