Search:

I am building a box with walnut and it has maple splines. I am planning on staining the walnut with a little walnut stain but don't want the stain on the splines how can I do this?

I actually just ordered the Irwins from Rockler today. They have a free shipping promotion right now so it was 99 bucks out the door. It says there back ordered, but when I asked about it they said...

I have seen a 3 or 4 episodes now and I agree he needs to calm down just a little. But I am sure it will get better. Either way it's nice to have a new show to watch.

I have to deal with cosmoline on a regular basis in my everyday job. We use WD40 or Kerosene both work great with lots of rags and nitrile gloves.

I do get PBS out of Portland, OR. But all I get is Roughcut and Woodright. Roughcut just started 3 weeks ago and half through the season.

Anyone know if this is available on Dish Network?

I run Windows7 and had the same issues. I dumped everything reformatted and it runs great now. I have to do this probably once a year other wise the computer starts running so slow I want to scream....

I would also suggest finding a local shop with a water jet. A program for just a round hole is easy and $75 seems kinda high.

I live in Salem, Oregon and picked one up about a month ago for $288 minus 10% military discount = $259.20 out the door. I have used it a few times and am very pleased with it so far. FYI if anyone...

The one I worked on bout a month ago I asked these questions. I was told the plan was a canned plan from ABC that they modified for the build. They were working on it for about 6 weeks before it ever...

Yes I have look at at it. Very nice kitchen and excellent thread

I was just involved with the one that was done here in Oregon at the OSD. It just aired on Halloween. It was quite the experience, but I agree it's a lot different then what you see on tv. Turns out...

I am starting to think about building my first set of kitchen cabinets. I am looking for a good book to guide me along the way and I am just looking for suggestions on what book.

Thanks

Sounds like a steal. Home depot and Lowes offers the 10% off all the time every time I buy something I show them my military ID and get 10% off. Just FYI

Not to hijack, but I have been thinking of putting my router on the left. I have a right tilt saw with 50" rip capacity, but the right of the saw is against a wall. Rather then add a table to the...

We had a HP photosmart and a Sony dye impression photo printer. Both cost way to much for refills. We now just e-mail all our pics to Walgreens and go pick them up an hr later. Way cheaper and I feel...

I have been watching the Ridgid jointer for ever it seems. About a month ago it drooped down to $360 and then when I checked on it today it was at $288 then with my military ID I got it out the door...

I have the Makita 18v I just framed 2 small bedrooms using 3" square drive screws not one broken screw or bit. I think you are over torquing or got crappy screws.

I agree granted I bought mine new, but I have had it for 6 years now. All I had to replace unexpected was a water pump impeller but was my fault. Other then that just regular maint. and...

Just made mine from scrap Corian roughed out on bandsaw and then used the original with a flush trim bit. Also drilled and tapped for leveling screws. Made about 12 or so in about an hr.

I have a high end Garmin and I love it except I have to pay to update the maps. So if I was to buy another I would get one that allows you to do this for free.

We have a above ground pool, but use saltwater now. We used to use chlorine but it seemed like we could never get it right and was trying to adjust it everyday. With the saltwater we never do...

Back when I was a mechanic in the army we used to take a couple zip ties and put them on the drive shafts of the HUMVEE's so while it spun it would slap the floor boards. The guys would bring it back...

They used the tubing from some romex cable. I saw that too and tried it one time when I needed to use a can worked great..

I tried the trash can but the air needed to escape so I cut a large hole in the lid and put a furnace filter in the hole. I still got chips everywhere couldn't get it to seal up well enough.