Search:

Type: Posts; User: George Gyulatyan; Keyword(s):

Page 1 of 14 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thank you all for the great responses! I looked...

    Thank you all for the great responses! I looked at the Jet manual and it suggests I turn the whole saw upside down to get to adjust the trunnions!

    I like the bevel sled idea. I think that's what...
  2. Yeh. Unfortunately in this case the trunnion is...

    Yeh. Unfortunately in this case the trunnion is mounted to the table, which is gonna make it a major PITA to get this aligned. I do have a project coming up where I am gonna need accurate miter cuts...
  3. Jet JPS-10TS ProShop

    Jet JPS-10TS ProShop
  4. Table saw blade changes front-back angle when tilting.

    Creekers, need help figuring out this one.

    I am making a new crosscut sled. I made two plunge cuts one at 90-deg another at 45-deg to figure out where I am going to route for zero-clearance...
  5. Replies
    6
    Views
    1,336

    Finished building my vacuum press from Joe...

    Finished building my vacuum press from Joe Woodworker V2 venturi kit.

    340279340278340280
  6. Replies
    35
    Views
    9,901

    My dad bought one to cut all the moldings for the...

    My dad bought one to cut all the moldings for the new house. It did the job. Still works. About the only issue with it is that it goes a bit too low now and the sawblade rubs on the bottom, which...
  7. Mine does the same thing. Fence. Let's just...

    Mine does the same thing.

    Fence. Let's just say once I got it to sit at 90 degrees, I haven't moved it. Luckily once the angle is locked in, it remains that way even if you remove/reinstall the...
  8. Not too long ago I was working with short (4.5")...

    Not too long ago I was working with short (4.5") pieces of Wenge that I needed to trim and cut stopped rabbets on them. Built a jig with two pieces of Baltic birch to cradle the pieces with a toggle...
  9. I certainly hope your experience is better than...

    I certainly hope your experience is better than mine. An update. This morning I was able to get a hold of a rather friendly fella (Dave) in tech support. Looks like they've updated their manual with...
  10. Replies
    14
    Views
    11,435

    I just use a lid for 5gal. plastic pail you can...

    I just use a lid for 5gal. plastic pail you can get at the borg to soak the blade in. It's the perfect diameter. Use warm water and some dishwasher liquid and go to town with a plastic bristle brush....
  11. Actually converting from Jointer to Planer mode...

    Actually converting from Jointer to Planer mode isn't that big a deal. It's pretty easy actually... but read my post about the overall tool.
  12. Don't buy it. I have the older version of 25-010...

    Don't buy it. I have the older version of 25-010 which looks pretty much identical except it's got a 3-knife HSS head and is green in color. If I knew then what I know now I wouldn't plunk down the...
  13. Replies
    9
    Views
    1,758

    Extended Jointer tables

    Ever since I got my Rikon 10" jointer/planer, I've been complaining that the combined table length is only 44"... (well, ONE of the many other complaints, but that's another story). So decided to...
  14. Beautiful piece!

    Beautiful piece!
  15. This! Indeed.

    This! Indeed.
  16. Replies
    36
    Views
    10,732

    That is one absofrickenlutely beautiful table....

    That is one absofrickenlutely beautiful table. Love the modern understated design. This kind of designs are so much harder to pull off as due to apparent simplicity everything must be spot on. And...
  17. I was recently cutting rabbets on some small...

    I was recently cutting rabbets on some small pieces of Wenge. I was getting a lot of tearout going the "right" direction, so I started doing very shallow climb cuts to start, and then cut the normal...
  18. Replies
    8
    Views
    1,996

    I would go with veneered MDF doors.

    I would go with veneered MDF doors.
  19. I am sure Rube Goldberg would have no problem...

    I am sure Rube Goldberg would have no problem building this!

    Yeah, Animusic is pretty cool. They've got some really great stuff even more complex than this... good music too.

    Here's a real life...
  20. If that was true we wouldn't have the housing...

    If that was true we wouldn't have the housing bubble.
  21. I have a Dewalt ROS that I just hook up to my...

    I have a Dewalt ROS that I just hook up to my shop-vac. No dust issues.
  22. Dude, stop with the all caps, and all ad-hominem...

    Dude, stop with the all caps, and all ad-hominem remarks and your flawed assumptions. I've read two of your posts in this thread and your assumptions are annoying and your caps above, just downright...
  23. Replies
    17
    Views
    3,510

    Gulp! .....

    Gulp!
    .....
  24. Replies
    23
    Views
    3,210

    Also, if you already have a compressor, the...

    Also, if you already have a compressor, the Venturi based systems make sense as you don't have to purchase a pump. Check Joe's site for a chart with CFM ratings and compressor requirements.
  25. Replies
    21
    Views
    4,062

    I wouldn't change a thing. Nice clean design,...

    I wouldn't change a thing. Nice clean design, great wood selection. I also like the hardware precisely because it is off the beaten path, somewhat unexpected and gives a fresh look to the piece. With...
Results 1 to 25 of 329
Page 1 of 14 1 2 3 4