Search:

Allen, Bob is correct, but I may add for 3 phase, swap any 2 "hot" wires to change the phase in order to change direction of the motor. All our motors we use offshore also has a ground wire.

Jack, is your blade a full kerf? like 1/8"? If your running a thin kerf blade like the ones that the box stores sell, then your blade is not opening up the kerf wide enough for your riving knife. ...

We used link belts on most all of our machines in a medium sized factory that I used to work at. They sure were handy, as we could build the correct size belt for our need. We stocked several width...

Only use a lithium grease on elect motors and use just a little bit.

If you don't mind spending a little money on a template for your router, you can buy jigs from Puritan CNC (puritancnc.com) to cut all your groves in your stiles. I got the jig for the Bahamas...

I had the same problem with my Mini Max. Changed the blade, problem went away.

5 minute epoxy does not cure in 5 minutes, it just sets up in 5 minutes, you will need to let it cure at least overnight, Read the manufacture's litacture. Also, as was already stated, insert the...

Pete, I know it is a drive, but if you come over to Pensacola. Meredith and Sons Lumber stocks all types of hardwoods. That is where I get my wood from. The address is 8701 N Palafox st.

Lynn,
If your looking for bearings for your Excalibur sliding table, I have the older model that uses 6 bearings and has the UHMW strip also and I replaced all my bearings, I got them from ...

Kent, that was a good one. I think I can relate.

Yea thanks Rick. Just what I needed.

Take the belt off, turn the cutter head pully and the motor by hand. Do you feel any binding, rough feeling? If not, the bearings are fine. Get a new belt, put the proper tension on it, and your...

Michael,
That is so "old School". Literally.

Mark, Good point, we auctually use the BSP fittings on some of our motors we get in from Europe. Dan, the Parker fitting Catalog is a good source for info., Always go to the manf literature and...

Easy, route your round over, rip it off, then plane the board, then reattach with glue. Use Dowels, biscuits or domino if you think you need some more reinforcement.

Okay, if you want the down and dirty scoop, here it is. Hydraulic fittings can be, 1. Pipe thread- NPT or NPTF 2. Boss (oring sealed)
3. JIC (37º flared) 4. Autoclave - for extremely high...

Great info. Thank you for sharing.

Joe, those are to nice to cut on..............

I have a 5 HP PM2700 shaper that I bough new. I love it. I also own 2 Delta 3 HP shapers. The digital spindal height read out and the fence make it a pleasure to use. The large table and the...

Same story here, they are a first class operation. I bought 2 filters from them.

Phil, for parts check with Original Saw Mfg. They sell a lot of parts to fit the older Dewalts, as they make their new saws that use the original Dewalt design. Good luck, I have one of the new...

I would not sweat it. Just go to to McMaster-Carr on line and order a new pulley. They list all the information you will need to measure your old pulley so you can order the same size. They also ship...

Don, Thanks for the advice. Seems like the oil based enamel is the standard. I wonder has anybody used a epoxy paint or a 2 part polyurthane like in the marine industry? Just thinking out loud. I...

I am building raised panel doors from popular to replace the MDF doors in my kitchen. Of course they will need to be painted white to match the rest of the kitchen. I have only used stains /...

I just received my 10" WW2 back from Forrest for sharpening. It only cost me $29 (freight back included). Slices hard mapel like butter. Turn around time about a week and a half.