Search:

Type: Posts; User: Jack Harper; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    1,252

    masquerade

    I am looking for masquerade party type masks. These need to be pretty ornate.
  2. Replies
    3
    Views
    1,252

    Masquerade Masks

    Hello,

    Does anyone know of a good source of masquerade mask vectors? Thanks.

    Jack
  3. Replies
    10
    Views
    5,109

    I don't remember where I found it, but I found it...

    I don't remember where I found it, but I found it in a large selection of sizes. I just googled to find it though.
  4. Replies
    10
    Views
    5,109

    I played around with some graphite and found that...

    I played around with some graphite and found that it does make a mark, just not a high contrast mark. I decided to do an experiment and cut some acrylic placed directly on top of the graphite...
  5. Replies
    9
    Views
    1,703

    Thanks Mike.

    Thanks Mike.
  6. Replies
    9
    Views
    1,703

    Which wood engraves darker?

    Does anyone know which wood will engrave darker, quarter sawn white oak, which is very hard, or Clear Vertical Grain Fir? Thanks.
  7. I'm in! Thanks.

    I'm in! Thanks.
  8. I'm in. Thanks!

    I'm in. Thanks!
  9. Replies
    7
    Views
    3,578

    A 4' x 8' ThinStone (8mm) panel weighs 165lbs or...

    A 4' x 8' ThinStone (8mm) panel weighs 165lbs or 5.15lbs psf.
  10. Replies
    8
    Views
    2,123

    Thanks everyone for your input. I really...

    Thanks everyone for your input. I really appreciate it.



    Scott- It actually ended up at around 2600 hours when all said and done. And yes, I quoted the job using a 24/7 schedule. I have done...
  11. Replies
    8
    Views
    2,123

    Scott - It is a pttern, it is kind of like the...

    Scott - It is a pttern, it is kind of like the postscript bubble pattern in Corel. The bubles are as large as 4" or so and smaller. The pattern will be back-lit and it would be difficult to get a...
  12. Replies
    8
    Views
    2,123

    Dave - Yes it is all the same depth. I wondered...

    Dave - Yes it is all the same depth. I wondered about a router. The pattern varies in width so you would have to use a smaller bit and do several passes in some areas and the bottom would have to be...
  13. Replies
    8
    Views
    2,123

    Deep Engraving Cast Acrylic

    I am trying to quote a large job deep engraving cast acrylic. I need to go about 1/16 (.063) deep into the 1/2" thick sheet. I did a time study for my 60 watt laser and found it will take me 1979...
  14. Replies
    24
    Views
    7,777

    Save your file as an 8 bit gray-scale .bmp file...

    Save your file as an 8 bit gray-scale .bmp file and you are good to go. Of course, you still need a proper file like the one Dee was kind enough to post or a Gantry Co file.
  15. Replies
    4
    Views
    2,234

    Thanks Belinda, but actually I will need about...

    Thanks Belinda, but actually I will need about 400 sq ft of the same veneer and the customer has yet to pick which one.
  16. Replies
    4
    Views
    2,234

    Thanks Anthony. And yes, we are very busy,...

    Thanks Anthony. And yes, we are very busy, definitely seeing a spike on the industrial side.
  17. Replies
    4
    Views
    2,234

    Exotic plywood

    Hello -Does anyone have a good source for exotic veneered wood, in something like 1/8", to laser etch and cut. Preferably, I would like the sheets pre-finished. Thanks.
  18. Replies
    19
    Views
    3,306

    You know, a little tweaking/embellishment there...

    You know, a little tweaking/embellishment there and you have a nice little homemade Advent calendar.
  19. Replies
    10
    Views
    1,399

    You might contact Vytek or Kern and inquire as to...

    You might contact Vytek or Kern and inquire as to a customer in you area that might have a large format laser engraver. While our 6' x 10' x 24" laser can handle it, were not exactly in the...
  20. Thread: Thanks

    by Jack Harper
    Replies
    10
    Views
    1,732

    Good question. I guess it really depends on...

    Good question. I guess it really depends on exactly what you were saying. If you were questioning the actual existence of a 100% black stone that was a true marble, then you were wrong. However, if...
  21. Thread: Thanks

    by Jack Harper
    Replies
    10
    Views
    1,732

    Brian, It is called "pure black" marble and I...

    Brian,

    It is called "pure black" marble and I buy by the pallet all the time. It is a true sedimentary stone i.e. marble. Just an FYI:)
  22. Replies
    6
    Views
    1,141

    I have spoken to Photgrav several times regarding...

    I have spoken to Photgrav several times regarding this problem. They say they will look at the problem sometime in the future...possibly. Version 2.11 will handle a little larger file than 3.0 but...
  23. Replies
    25
    Views
    4,389

    Steve, Look up your local custom mill work...

    Steve,

    Look up your local custom mill work company. These companies will make custom molding in almost any shape. By having them run the stock out in the shape you need, all you have left is to...
  24. I'm in. Thank you

    I'm in. Thank you
  25. Replies
    9
    Views
    1,251

    I have not tried it but I found...

    I have not tried it but I found www.e-nesting.com. It looks like it is still in beta though.
Results 1 to 25 of 397
Page 1 of 16 1 2 3 4