Results 1 to 15 of 15

Thread: Greenlee Bench Chisels

  1. #1
    Join Date
    Mar 2007
    Location
    Midlothian, TX
    Posts
    359

    Greenlee Bench Chisels

    I bought a set of Greenlee bevel edge bench chisels in 1980, 1/8" to 1 1/4". They were made in Sheffield, England. I'm just curious as to who made them. I'm pretty sure it wasn't the Greenlee folks.They look a lot like older Marples but with beech handles and logo burned into them. One of my kids lost the 1/2" size. I picked up an older Marples to fill in until I can find one that matches. The Greenlee's are a little above average quality. Mine are grubbier now than the ones in the small photo.
    Deane
    Attached Images Attached Images
    Originality is the art of concealing your source.
    Franklin P. Jones
    Comments & criticism on postings welcomed.

  2. #2
    Join Date
    Jan 2010
    Location
    Wisconsin - Milwaukee Area
    Posts
    78
    Deane,

    They sure look like the Marples chisels. Are they marked on the blade, too?

    I have a couple of Greenlee's that were made in Rockford. IL. Those are among my favorite chisels: the steel is very tough and holds an edge really well. A couple of other Greenlee items I have drawknife and auger bits are all above average.

    I've read in a number of places that Marples steel quality used to be very good but then at some point declined.

    Alfred

  3. #3
    Join Date
    Feb 2003
    Location
    Ridgeville SC
    Posts
    85
    Yes,

    They were made by Marples. Someone was selling these for $28/set of 7 chisels as a closeout and I purchased several sets to resell. Decent steel and durable handles.
    Gentleman Jim

  4. #4
    Join Date
    Mar 2007
    Location
    Midlothian, TX
    Posts
    359
    Quote Originally Posted by Jim Holman View Post
    Yes,

    I purchased several sets to resell. Decent steel and durable handles.
    You wouldn't happen to still have a 1/2" one laying around?
    Deane
    Originality is the art of concealing your source.
    Franklin P. Jones
    Comments & criticism on postings welcomed.

  5. #5
    Join Date
    Jan 2009
    Location
    Williamsburg,Va.
    Posts
    12,402
    My 1960's Marples are about as good as any chisels that are made from 01,which is what I think these are made from. I still use them a lot.

  6. #6
    Join Date
    Feb 2003
    Location
    Pleasant Grove, UT
    Posts
    1,503
    Could they have been Footprints?
    It came to pass...
    "Curiosity is the ultimate power tool." - Roy Underhill
    The road IS the destination.

  7. #7
    Join Date
    Dec 2004
    Location
    Bakerville, CT
    Posts
    416
    Quote Originally Posted by Deane Allinson View Post
    I bought a set of Greenlee bevel edge bench chisels in 1980, 1/8" to 1 1/4". They were made in Sheffield, England. I'm just curious as to who made them. I'm pretty sure it wasn't the Greenlee folks.They look a lot like older Marples but with beech handles and logo burned into them. One of my kids lost the 1/2" size. I picked up an older Marples to fill in until I can find one that matches. The Greenlee's are a little above average quality. Mine are grubbier now than the ones in the small photo.
    Deane

    I own a few Greenlee chisels that appear nearly identical to the original Marples blue handled chisels - the steel, shape of the blade, and handle material/shape are - to my eye - the same.
    1.jpg2.jpg3.jpg4.jpg

    Sorry for the crappy pictures.....

    I like Greenlee chisels overall (a fairly broad statement as Greenlee manufactured/badged several different "types" of chisels over the years). Most of my old Craftsman chisels were made by Greenlee as well.....

  8. #8
    Join Date
    Mar 2004
    Location
    DuBois, PA
    Posts
    1,898
    Quote Originally Posted by Todd Davidson View Post
    I own a few Greenlee chisels that appear nearly identical to the original Marples blue handled chisels - the steel, shape of the blade, and handle material/shape are - to my eye - the same.
    1.jpg2.jpg3.jpg4.jpg

    Sorry for the crappy pictures.....

    I like Greenlee chisels overall (a fairly broad statement as Greenlee manufactured/badged several different "types" of chisels over the years). Most of my old Craftsman chisels were made by Greenlee as well.....
    I have a set of the same green handled-Greenlees. Picked them up a year or two for $14 or $15 for a set of 4. Only one looked like it had any wear/sharpening. I agree they are nearly identical to the Marples, except for the color, and they take & hold a edge very well.
    If the thunder don't get you, the lightning will.

  9. #9
    Join Date
    Feb 2007
    Location
    Crystal Lake, IL
    Posts
    577
    The older Greenlee chisels from Rockford, Illinois, are made with excellent quality steel. I have, over the past 10 years or so, put together one fine set of them. I have most of the sizes, including some oddball ones like 5/8" and 7/8". I also, recently found some Greenlee framing chisels and gouges that are practically unused, except by oxygen and water to make surface rust. I'm doing timberframing work on a new project, and needed some larger sizes. I found a 1.5", 2" and 3" for $15 apiece, as well as 2 larger gouges for the same. I was so elated I did an Irish jig when I got them home.

    My only knock, which really isn't a knock at all, on the older style Greenlee's is that their original fit, finish and grind wasn't all that great from the factory. Read this to say that they take a little more than usual work to get them flat, and I almost always have to regrind the bevel......even on a full set of 5 Greenlee Butt chisels that were in the box, new old stock, sitting on a shelf for 40 plus years in the basement of an old, old hardware store near me. Once flattened, and the bevels reground straight and true, they are made from outstanding quality steel. They stay sharper longer than my (former) set of LN chisels, which I gladly sold and got all my money back from the bay....

    These chisels discussed in this thread are not the same tools. If you can find the older ones from Rockford, I'd highly recommend them.
    Jeff

  10. #10
    Quote Originally Posted by Jeff Heath View Post
    …a full set of 5 Greenlee Butt chisels that were in the box, new old stock, sitting on a shelf for 40 plus years in the basement of an old, old hardware store near me. Once flattened, and the bevels reground straight and true, they are made from outstanding quality steel. They stay sharper longer than my (former) set of LN chisels, which I gladly sold and got all my money back from the bay....
    That's a stealth gloat if I ever heard one.
    Well done!
    "For me, chairs and chairmaking are a means to an end. My real goal is to spend my days in a quiet, dustless shop doing hand work on an object that is beautiful, useful and fun to make." --Peter Galbert

  11. #11
    Join Date
    Dec 2010
    Location
    South Coastal Massachusetts
    Posts
    6,824
    You suck, dude.

    I hope your Grandkids open
    paint cans with these.

    Some people have all the luck,
    and the good Hockey teams.

  12. #12
    Join Date
    Jan 2004
    Location
    Peachtree City, GA
    Posts
    1,582
    Bob Lang's chisels that appear in every photo shoot appear to be the green handled Greenlee's. Works nicely for him.
    Maurice

  13. #13
    Join Date
    Jan 2010
    Location
    Wisconsin - Milwaukee Area
    Posts
    78
    Jeff,
    You make another good point about buying good vintage chisel - Greenlees among them- they range of sizes and shapes is much larger than what is available now. I only have a handful of chisel but they include a long 1/8 inch and a shot 2 inch. For some of the long and some wider chisels sizes the choices among new chisels are sparse at best.
    About Greenlees: they seem to be more abundant in the Midwest because most were probably sold here originally.
    I also have a feeling that some hardware chains with their own line of chisels, e.g. Pritzlaff, were made by Greenlee. I have a few Prtizlaffs that came with a strangely conical handle but the blade looks like and is as good as my Greenlees even though it has a Ptitzlaff star stamp on the socket.

    Alfred

  14. #14
    Join Date
    Jan 2010
    Location
    Wisconsin - Milwaukee Area
    Posts
    78
    Short correction to my previous post:
    I had some trouble with the small keyboard on my tablet. One of the typos needs to be corrected: the line in which a 'shot 2 inch chisel' is mentioned should have read 'short 2 inch chisel'.

    Apologies


    Alfred

  15. #15
    Join Date
    Feb 2007
    Location
    Crystal Lake, IL
    Posts
    577
    Quote Originally Posted by Jim Matthews View Post
    You suck, dude.

    I hope your Grandkids open
    paint cans with these.

    Some people have all the luck,
    and the good Hockey teams.
    Uh, excuse me, sir. You mean, the BEST hockey team. Go Blackhawks!!

    A huge Hawks fan and former player for 40 years....
    Jeff

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •