Hello to every one,
Suddenly during cutting 3 mm acrylic, head stopped moving . And when i restarted the machine
LCM Version <<5>> was displayed and the machine was hung.
Kindly help for above problem..
Regards...
Hello to every one,
Suddenly during cutting 3 mm acrylic, head stopped moving . And when i restarted the machine
LCM Version <<5>> was displayed and the machine was hung.
Kindly help for above problem..
Regards...
Did the laser also stop firing when the head stopped?
Does it try to boot? Any movement of the x or y axis or the table itself?
Is perhaps the table touching the upper limit switch?
Move the head by hand to the home position and try start again.
It could be something simple like a dead Servo motor or a dirty/faulty one or a loose/broken cable or it could be something more serious like the motherboard.
Very difficult to diagnose with the little info you give....
Rodney Gold, Toker Bros trophies, Cape Town , South Africa :
Roland 2300 rotary . 3 x ISEL's ..1m x 500mm CnC .
Tekcel 1200x2400 router , 900 x 600 60w Shenui laser , 1200 x 800 80w Reci tube Shenhui Laser
6 x longtai lasers 400x600 60w , 1 x longtai 20w fiber
2x Gravo manual engravers , Roland 540 large format printer/cutter. CLTT setup
1600mm hot and cold laminator , 3x Dopag resin dispensers , sandblasting setup, acid etcher
Dear Rodne,
Did the laser also stop firing when the head stopped? Yes
Does it try to boot? No
Any movement of the x or y axis or the table itself? No
Is perhaps the table touching the upper limit switch? No
As the machine hung up, I immediately power off the machine.
Then again when I started the machine. the machine stopped booting displaying the message
LCM Version <<5>>
and then I turn on/off the machine many times, the machine failed to boot.
Regards
Sunil Jain
Ensure emergency stop is not depressed. I once spent ages trying to determine why spirit would not boot and almost call tech support until i found the switch had got pressed when laying a pex sheet over the machine. Felt like an idiot that day. If it's not that then problem sounds serious.
Sam Gardner Seychelles Islands, Indian Ocean
1xGCC Spirit GLS 80W, 2xGCC Spirit 25W, 1 GCC Jaguar IV vinyl cutter,
1 Shenhui 4x4 CNC router, Sublimation, Melco Amaya Embroidery
Unique by a thousand miles!
Sounds like a motherboard problem to me , especially if there is no attempted boot or movement. There is a set of lights on the motherboard that acts like a diagnostic , I dont have the manuals with me right now so don't know what they mean and what should be on but mail GCC or your local agent and ask em to help. GCC themselves are quite good with problems if your local guys arent'
Rodney Gold, Toker Bros trophies, Cape Town , South Africa :
Roland 2300 rotary . 3 x ISEL's ..1m x 500mm CnC .
Tekcel 1200x2400 router , 900 x 600 60w Shenui laser , 1200 x 800 80w Reci tube Shenhui Laser
6 x longtai lasers 400x600 60w , 1 x longtai 20w fiber
2x Gravo manual engravers , Roland 540 large format printer/cutter. CLTT setup
1600mm hot and cold laminator , 3x Dopag resin dispensers , sandblasting setup, acid etcher
You can find maintenance manuals here
http://www.meistergram.com/page.aspx?page_id=49
Rodney Gold, Toker Bros trophies, Cape Town , South Africa :
Roland 2300 rotary . 3 x ISEL's ..1m x 500mm CnC .
Tekcel 1200x2400 router , 900 x 600 60w Shenui laser , 1200 x 800 80w Reci tube Shenhui Laser
6 x longtai lasers 400x600 60w , 1 x longtai 20w fiber
2x Gravo manual engravers , Roland 540 large format printer/cutter. CLTT setup
1600mm hot and cold laminator , 3x Dopag resin dispensers , sandblasting setup, acid etcher
Thanks Rodne for all the replies
I have called the GCC for problem
regards