Results 1 to 14 of 14

Thread: Can I cut a beveled edge into acrylic using the laser

  1. #1
    Join Date
    Aug 2012
    Location
    Ocala Fl
    Posts
    229

    Can I cut a beveled edge into acrylic using the laser

    I've figured out how to create bevels in Corel but not sure if the laser would cut it. I would think that it would have to vary the power to cut progressively deeper.
    Ernie Martinez
    Ocala Florida
    Epilog Mini 24 50W
    Windows 7 Corel X6, PhotoLaser +v9
    Laguna IQ CNC Router
    Vectric Vcarve Pro
    Smithy Granite 1324 Mill/Drill/Lathe
    Grizzly GO621X Bandsaw

  2. #2
    You could on small piece by attaching the piece to a "wedge" not easy or productive.
    Need the pieces to be small and will not have a totally finished edge. Epilog works
    of a grey scale so it may be possible through rastering a gradient, then again quite
    a bit of time involved and no finished edge. If this is for a quantity and a decent
    budget contact a local acrylic supplier and see what they can do for your blanks.

    Do you have a router? That would be possible with an acrylic bit, then you will need
    to flame polish the edge.
    Martin Boekers

    1 - Epilog Radius 25watt laser 1998
    1 - Epilog Legend EXT36 75watt laser 2005
    1 - Epilog Legend EXT36 75watt laser 2007
    1 - Epilog Fusion M2 32 120watt laser with camera 2015
    2 - Geo Knight K20S 16x20 Heat Press
    Geo Knight K Mug Press,
    Ricoh GX-7000 Dye Sub Printer
    Zerox Phaser 6360 Laser Printer
    numerous other tools and implements
    of distruction/distraction!

  3. #3
    Join Date
    Mar 2005
    Location
    Gig Harbor, WA
    Posts
    1,157
    In short "No", not that would look good.
    Mark
    In the Great Northwest!

    Trotec Speedy C25, Newing-Hall 350 (AMC I & HPGL), NH-CG-30 (Carbide Cutter Sharpener)
    Sawgrass 400 Gel Ink Printer, CS5, 5/9/x6 CorelDraw

  4. #4
    Join Date
    Oct 2007
    Location
    Cincinnati, Ohio
    Posts
    1,843
    For the very few times I've been asked to bevel an edge, I just tapped it on my bench sander for each side, cleaned up and done. Careful to be sure it's straight, but again I rarely have to do this.
    Tim
    There are Big Brain people & Small Brain people. I'm one of the Big Brains - with a lot of empty space.- me
    50W Fiber - Raycus/MaxPhotonics - It's a metal eating beast!
    Epilog Fusion M2 50/30 Co2/Fiber - 2015
    Epilog Mini 24 – 35watt - 2006 (Original Tube)
    Ricoh SG3110DN
    - Liberty Laser LLC

  5. #5
    How awesome would it be if the next generation of lasers included an automatically tilting mirror plus focal length correction, distance compensation in the driver? You could do all kinds of new and interesting things if it could cut at angles! Dave
    Epilog 35 W 12x24
    Adobe Illustrator
    Dell PC

  6. #6
    Quote Originally Posted by David Fairfield View Post
    How awesome would it be if the next generation of lasers included an automatically tilting mirror plus focal length correction, distance compensation in the driver? You could do all kinds of new and interesting things if it could cut at angles! Dave
    Think of the power it would take to cut 1/4" acrylic on an angle!

  7. #7
    Quote Originally Posted by Wes Mitchell View Post
    Think of the power it would take to cut 1/4" acrylic on an angle!
    Would be a little under 3/8"
    Equipment: IS400, IS6000, VLS 6.60, LS100, HP4550, Ricoh GX e3300n, Hotronix STX20
    Software: Adobe Suite & Gravostyle 5
    Business: Trophy, Awards and Engraving

  8. #8
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,686
    Quote Originally Posted by Ross Moshinsky View Post
    Would be a little under 3/8"
    That depends entirely on the angle.

  9. #9
    Join Date
    Sep 2011
    Location
    naples florida
    Posts
    278
    like they all say it depends on the size. but I do some up to 4x4 inches not in a 45 degree only up to about 30 degree with a jig of 30 degree and little clamp and cut up to 1/4 inch acrylic in two runs just straight cuts. the only probleme is that the jig and clamp has to be precise in order to get a perfect edge out
    greetings
    walt

  10. #10
    Cutting thin material, like mat board, at an angle would be so useful. Doesn't have to be 1/4 plexi. Dovetails would be possible, too, I suppose, and that would be terrifically useful for small decorative boxes and dollhouse furniture. Well, just a daydream for now but eventually...

    Dave
    Epilog 35 W 12x24
    Adobe Illustrator
    Dell PC

  11. #11
    I recently came across the Microsoft Research Lab's laser cutter use notes. They include a description of how to get a quick bevelled edge. I haven't tried it (our laser's not set up yet), but I'm posting the instructions below. There are some specific instructions for their machine that you'll have to adapt.

    Quick Bevel Cut: To produce a beveled finish atop a normal cut:
    a. Cut the part out normally. You might have to design small tags to hold the part in place for the next operation if the part will shift much after the initial cutout. Leave everything untouched in the cutter after the cuts.
    b. Get into FOCUS mode (push Z) and lower the floor by 1.0"—10 pushes of the Floor down button at 0.1" steps.
    c. Make a copy of the vectors you want to bevel, change to a unique color, and exactly overlay these atop your original object(s).
    d. Move these new vectors in X and Y on your drawing, up .01" and to the left by 0.015" (add -0.015 to X and +0.01 in Y in the SIZE-POSITION window). This accounts for this machine‘s AZ/EL (L/R) offset per 1.0" out-of-focus for our printer.
    e. Vector-cut only that unique color at 2x to 4x speed, same power or a half to a quarter of total power.
    f. Return the floor back to the normal focus height.
    Center for Experimental Nuclear Physics and Astrophysics - University of Washington
    Kern 400W 4'x8' HSE with metal cutting add-on and rotary stage
    2-axis CNC mill, 2 manual mills, 3 lathes, other standard shop tools, . . . and a 7.5 MeV tandem Van de Graaff particle accelerator

  12. #12
    Join Date
    Aug 2012
    Location
    Ocala Fl
    Posts
    229
    I don't know enough about Corel, but I would think that a Macro could be written that could do this automatically. Create X number of lines of different colors which are assigned different power levels using color mapping, then create the bevel drawing using the different colored lines.
    Ernie Martinez
    Ocala Florida
    Epilog Mini 24 50W
    Windows 7 Corel X6, PhotoLaser +v9
    Laguna IQ CNC Router
    Vectric Vcarve Pro
    Smithy Granite 1324 Mill/Drill/Lathe
    Grizzly GO621X Bandsaw

  13. #13
    Join Date
    Nov 2006
    Location
    Maple, Ontario, Canada
    Posts
    1,010
    Why struggle with that when you can find real beveler on ebay from time to time for under 200.00
    It will pay for it self in a jiffy if you bevel most of your plates.
    Trotec Speedy 300 - 60w, with Quatro CSA-626 fume extraction
    Xenetech 1625 x2,
    New Hermes TX pantograph, CG4 cutter grinder
    Brady Globalmark2 label printer,
    Assortment of custom tooling , shears & punches, heat bender.
    Software: Xenetech XOT, Corel X3, Bartender label software

  14. I've done them before by drawing a little grayscale gradient in Illustrator across the area I want the angle and then engraving that (the black part being the lowest part of the angle). It works in a pinch, but it rarely looks that great, usually requires a lot of trial and error, and it would usually be far faster to just throw it on a sander or mini table saw.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •