Results 1 to 11 of 11

Thread: Finish for kitchen cabinets

  1. #1
    Join Date
    Dec 2004
    Location
    NW Indiana
    Posts
    1,050

    Finish for kitchen cabinets

    I've started on the kitchen cabinets. Lately I've been thinking about using something besides poly. I would like to spray them. I've been looking at water-based lacquer is this a good finish for a kicthen to stand up to grease,etc.. But any suggestion would be appreciated. By the way the cabinets are maple with no stain...........

  2. #2
    Join Date
    Mar 2003
    Location
    odessa, missouri
    Posts
    1,910
    Blog Entries
    3
    i take it your not satisfied with the poly look or results?

    sometimes a change comes with satisfaction and disapointment.

    first question is what are you looking to achieve with a different finish?

    second question ...what properties would you like to keep of the poly if any?

    everyone has there choices, so a better definition of your needs would be required.like wood and preferences, everyone will give a different answer....jack

  3. #3
    Join Date
    Mar 2003
    Location
    SE PA - Central Bucks County
    Posts
    65,688
    My kitchen cabinets were finished with water bourne acrylics; Target Coatings PSL (now USL) and Fuhr International 9100. These products spray nicely, clean up easily and are very durable. Target also has some water bourne products that approach pre-cat lacquer durability without the associated environmental and personal danger. (Pre-cat lacquer is what is put on many factory cabinetry...you will almost never find anything "polyoneverything" on commercial work) It's a myth that poly is the most durable finish and it brings its own host of problems as does any finish.
    --

    The most expensive tool is the one you buy "cheaply" and often...

  4. #4
    Join Date
    Dec 2003
    Location
    Hudson Valley, Upstate NY
    Posts
    240
    I just finished some kitchen cabs with a satin ("medium rubbed") Sherwin-Williams pre-cat lacquer- VOC content of 675--toxic-o-rama! It was the first time I'd sprayed, the first time I had used lacquer and I was pleased with the results. Lacquers dry rapidly so you can recoat several times in one day. If you use something like this, please follow every rule about proper ventilation- this stuff was no-laughing matter volatile. Also, if you intend to thin, use the proprietary thinner.

  5. #5
    Join Date
    Mar 2003
    Location
    SE PA - Central Bucks County
    Posts
    65,688
    Pre-cat lacquers really shouldn't be sprayed in or around your home...they really require proper ventilation as well as safety gear. In fact, I'll go so far as to say they really aren't a good choice for a non-pro shop that doesn't have a formal spray booth with all the works. Nasty stuff. That said, I know a lot of folks do use these products...I can only hope they are very, very careful...
    --

    The most expensive tool is the one you buy "cheaply" and often...

  6. #6
    Join Date
    Mar 2004
    Location
    Cockeysville, Md
    Posts
    1,805
    I've sprayed Pre-Cat, Post-Cat and NC lacquer and it's by far my favorite finish for all the reasons Walt mentioned; fast dry time, sands easy between coats, durable and imparts a very very slight amber/warm tint without clouding the stain. On bare wood it makes the grain pop nicely. Since subsquent coats of Lacquer disolve the previous layer, if you mess up somehow, sand away the blemish and keep spraying.


    Jim's concerns are very valid! Turn off anything with a pilot light (stove, water heater, furnace, etc) along with any electric applioances like your fridge. Spray during moderate temps and humidty.

    I've never liked the finish of poly, looks too plastic for my tastes

    Brian
    The significant problems we encounter cannot be solved at the same level of thinking we were at when we created them.

    The penalty for inaccuracy is more work

  7. #7
    Join Date
    Mar 2003
    Location
    odessa, missouri
    Posts
    1,910
    Blog Entries
    3
    pre-cat doesnt disolve between coats and both poly and pre-cat ive found both look like plastic.

    as far as a spray both.....most paint crews dont pre-finish. cabinets are in the most part are finished on the job site. same safety care is required reguardless whether water base or flammable

    i use water base contact adhesive yet it still makes me ill....jack

  8. #8
    Join Date
    Mar 2003
    Location
    SE PA - Central Bucks County
    Posts
    65,688
    Quote Originally Posted by jack duren
    same safety care is required reguardless whether water base or flammable

    i use water base contact adhesive yet it still makes me ill....jack
    Not necessarily true...it depends on the particular product you are using. With solvent-based finishes you have both VOC (volatile organic compounds) and explosive issues to deal with. The latter is clearing something not easy to deal with in a home-shop situation. With water bourne products you may have VOC, but many of them these days are even "cleaner" than the latex paint you buy at the 'borg. Zero or near-zero VOC is becoming quite common. You still need to wear a respirator, but more and more it's for particulate protection rather than from VOC. But the explosive element is gone.

    In the case of your water based contact cement, you still have some pretty nasty stuff just suspended in the water for application convenience. The same can hold true for finishes, but again, it depends on the product. Most, if not all, water borne finishes are acrylic based and the latest products are wonderful from a safety standpoint!
    Last edited by Jim Becker; 05-22-2005 at 11:52 AM.
    --

    The most expensive tool is the one you buy "cheaply" and often...

  9. #9
    Join Date
    Mar 2003
    Location
    odessa, missouri
    Posts
    1,910
    Blog Entries
    3
    considering most finishing is done within 16" to 24" from ones nose i think ill stick with a mask and proper ventilation .....jack
    Last edited by jack duren; 05-22-2005 at 12:00 PM.

  10. #10
    Join Date
    Feb 2003
    Location
    Eagle River, Alaska
    Posts
    731
    I just sprayed a set of kitchen cabinets with Fuhr’s 375 (waterborne pre-cat lacquer). It’s the first time I have used it or any waterborne products, was very happy with the results.

    It sprays well, cleans up with water and about 10 percent household ammonia.

    My finish schedule was.

    Sand to 220, I coat of Zinsser Seal coat (a 2# cut of shellac) then sanded with fine grit sanding sponge.
    The seal coat greatly helps reduce sanding from grain rising.

    Two coats of 375 sanding with 400 girt paper between coats.

    The second and final coat of 375 came of the gun so well that no rubbing out of the finish was necessary. I use a satin finish and sure doesn’t look like plastic to me.

    The 375 is an approved by KCMA if that means anything.
    Last edited by Richard McComas; 05-22-2005 at 1:17 PM.
    Rich
    ALASKANS FOR GLOBAL WARMING

    Eagle River Alaska

  11. #11
    Join Date
    Feb 2003
    Location
    Chappell Hill, Texas
    Posts
    4,741
    Russ, I usually use pre-cat lacquer. It's fast, it's forgiving, and it's tough. I've also used latex paint, oil based paint, shellac, milk paint and pigmented lacquer. For a kitchen remodel I did back in '96 I even used automotive paint.

    As Richard eluded too, the KCMA (Kitchen Cabinet Manufacturer's Association) has set up guidelines for the different types and grades of finishes. A search on the net will tell you what those guidelines are, then you can ask your supplier which finishes meet the standard you choose to finish to.

    Todd

Similar Threads

  1. Tung Oil, BLO, Danish Oil - is there a difference
    By Roger Barga in forum Project Finishing
    Replies: 15
    Last Post: 11-12-2012, 1:15 PM
  2. Thoughts on my projects finish
    By John Lubeski in forum Project Finishing
    Replies: 5
    Last Post: 06-19-2008, 4:52 PM
  3. Shop Cabinets - Pics
    By Denny Lawson in forum General Woodworking and Power Tools
    Replies: 14
    Last Post: 12-14-2004, 11:44 AM
  4. Finish for Maple Kitchen Cabinets?
    By Richard McComas in forum General Woodworking and Power Tools
    Replies: 5
    Last Post: 11-14-2004, 12:54 AM
  5. Tung Oil Finish Practicality
    By Jim Young in forum General Woodworking and Power Tools
    Replies: 14
    Last Post: 08-07-2003, 12:54 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •