Results 1 to 12 of 12

Thread: Veritas quick release sliding tail vise?

  1. #1

    Veritas quick release sliding tail vise?

    My current top is a 3" laminated plywood sandwich that is not flat, up to 1/8 variation. I am replacing it with two IKEA countertops that I will laminate and flatten. IKEA was the quickest cost effective way to get 3" top. I also decided also to replace my current twin screw end vise with a tail vise since I am disrupting my usual activities, hence the question.

    Any opinions about Veritas quick release sliding tail vise? I am also considering a simple quick release steel vise as a tail vise.

    Thanks.

  2. #2
    I think I just convinced myself to combine twin screw and tail vise instead as seen in this video.
    Pretty ingenious.
    https://www.youtube.com/watch?v=8JXxPPMkRAU

  3. #3
    The Veritas piece would be my choice by a long shot.

  4. #4
    A better question would be: Do I need a tail vise?

  5. #5
    Quote Originally Posted by ken hatch View Post
    A better question would be: Do I need a tail vise?
    True, that is a good question. Biggest appeal of the tail vise for me is the ability to have dog holes very close to the edge. My current holes are two inches from the edge and I find it rather limiting.

  6. #6
    Join Date
    Sep 2007
    Location
    Longview WA
    Posts
    27,347
    Blog Entries
    1
    Quote Originally Posted by ken hatch View Post
    A better question would be: Do I need a tail vise?
    The answer to such a question is different for each person.

    My tail vise tends to get more use than my face vise. A person making different projects is likely to have different needs.

    jtk
    "A pessimist sees the difficulty in every opportunity; an optimist sees the opportunity in every difficulty."
    - Sir Winston Churchill (1874-1965)

  7. #7
    Quote Originally Posted by Jim Koepke View Post
    The answer to such a question is different for each person.

    My tail vise tends to get more use than my face vise. A person making different projects is likely to have different needs.

    jtk
    Do you use it for flattening between dogs? Reason I was thinking of moving my twin screw is because they way my bench is positioned I am not getting much use out of it.

  8. #8
    Join Date
    Sep 2007
    Location
    Longview WA
    Posts
    27,347
    Blog Entries
    1
    Quote Originally Posted by Reinis Kanders View Post
    Do you use it for flattening between dogs? Reason I was thinking of moving my twin screw is because they way my bench is positioned I am not getting much use out of it.
    Yes, and I also use it for holding pieces when dovetailing.

    Mostly this is because my lighting is better at the tail end. There is also a bit more room at that end.

    The positioning of a bench can have quite an influence on how a worker performs their tasks.

    jtk
    "A pessimist sees the difficulty in every opportunity; an optimist sees the opportunity in every difficulty."
    - Sir Winston Churchill (1874-1965)

  9. #9
    Join Date
    Dec 2010
    Location
    South Coastal Massachusetts
    Posts
    6,824
    Quote Originally Posted by ken hatch View Post
    A better question would be: Do I need a tail vise?
    That's a VERY good question.

  10. #10
    Join Date
    Dec 2010
    Location
    South Coastal Massachusetts
    Posts
    6,824
    Quote Originally Posted by Reinis Kanders View Post
    True, that is a good question. Biggest appeal of the tail vise for me is the ability to have dog holes very close to the edge. My current holes are two inches from the edge and I find it rather limiting.
    I currently have two benches.
    One has the Veritas sliding tail vise, the other has the inset Veritas inset vise.

    The inset vise is inexpensive and retrofits easily.
    It is worthless without the stop which could be replaced DIY, if necessary.

    It exerts tremendous clamping pressure.

    If you can pass by the side where the screw handle
    dangles, without taking out a pants pocket
    it would get my vote.

    The Veritas sliding tail vise is a much more involved,
    stout product that is only as good as the installation.

    If there's misalignment - it can be balky.

    If you're retrofitting - the inset vise is (relatively) easy to install.

    Veritas also makes a set of bench dog hardware that
    could make the vise surplus to requirements.

    A good stop over the most exposed corner of your bench
    and a couple of "Wonder dogs" might be enough.

    I'm finding that to be the case, in my current project.

    http://www.leevalley.com/us/wood/pag...29&cat=1,41637
    Last edited by Jim Matthews; 01-11-2015 at 5:03 PM.

  11. #11
    Quote Originally Posted by Jim Matthews View Post
    That's a VERY good question.
    Jim,

    Thanks, sometimes the answer is yes, sometimes no, and I expect many times the answer is: I haven't a clue.

    ken

  12. #12
    Join Date
    Jan 2005
    Location
    A suburb of Los Angeles California
    Posts
    644
    Quote Originally Posted by Reinis Kanders View Post

    Any opinions about Veritas quick release sliding tail vise? I am also considering a simple quick release steel vise as a tail vise.
    I have one and installed in on an Ikea-like bench top. The install was easy, the quick-release works well, and it's a fine performer.
    If you want a tail vise, this is a good way to go.
    AKA - "The human termite"

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •