Cheers! Mind you, shorts are much easier to cut upright in the tail vise, but I start them the same way.
Bumbling forward into the unknown.
Glad to see others posting their videos.
If this was available a decade ago my sawing would likely be a lot better.
jtk
"A pessimist sees the difficulty in every opportunity; an optimist sees the opportunity in every difficulty."
- Sir Winston Churchill (1874-1965)
OK that tears it. Now it's official- I grew up in the wrong era! Video instructions for various woodworking skills AND how to properly light a cigar (to achieve that perfectly symmetrical ash on your Hoya De Monterey Double Corona)!!
Apparently all the manly arts I've spent my 55 years learning are now available via on demand video! If there's You tube for training dogs/hunting birds, buying a good suit and marrying the right girl, then my value as a father to our two boys just became obsolete! No wonder they never listen to me - they already learned everything on the internet.
Brian, your a man after my own heart -whiskey, cigars and woodworking- what else do you need?
Cheers, Mike
I think we may be missing one.....how to pan-sear steaks
Cheers!
Bumbling forward into the unknown.
Did i notice a carpet on the workshop floor there Brian?
On the sawing. I'm relatively new to back saws (bought a set of Veritas saws last year), but with a fair amount of handsawing from a very young age. I seem to do ok on getting started. I had some initial problems with catching and bouncing, but unloading the saw as recommended by various seems to help that enormously as long as I don't mess it up.
One set up issue that seems to matter a lot in my case is to place the work set at the right height. I've been using a temporary bench that's much too high, and find that it causes a tendency for the saw to drift off the line as i go down a longer cut. At that stage the game is lost - attempted straightening inevitably results in a twisted cut. When i check i always seem to have managed to pull my elbow in too tight to my body, and to have it tensed too much.
Standing on something to relatively speaking lower the work seems to resolve the issue most of the time - it permits properly relaxing my arm and the saw then (most of the time) holds its line....
Last edited by Brian Holcombe; 03-01-2015 at 3:48 PM.
Bumbling forward into the unknown.
Ron,
Pull stroke start for rip.Different strokes for different folks.
That was impressive. Following the line even on the back side ! Beautiful saws with out a doubt.
What my little pea brain noticed . . . completely unrelated to performance and obviously perfect results was that . . .
when visually compared with the stationary , very nice, Powermatic cabinet saw base in the back ground . . .
your vise/bench moves not only back and forth but up and down. A small amount but discernible.
Meaningless but I couldn't help noting it.
Sharpening is Facetating.Good enough is good enoughButBetter is Better.
Brian
and everyone did you see that ?
Sawing through 5/4 walnut with the Dovetail saw(ha, ha nice one)I have one on how to light a cigar as well, if more help is needed.
Well forgive me but now I am obsessed with it . . .
besides what appeared to be less effort cutting the wood than Ron's vid
there was zero flex (effectively) in the bench/vise/work compared against the stationary line of the shelf support in the back ground in your vid.
Shoulder vise / Klausz bench = good.
PS: I am curious . . . Brian, did you sharpen that saw or is that stock or did someone else sharpen it ?
Sharpening is Facetating.Good enough is good enoughButBetter is Better.
Lol! I did sharpen it a few weeks ago. I ran through Mike's walk-through and it's been cutting fantastically since (thanks Mike!).
Bumbling forward into the unknown.
It shows.Mike's walk-through and it's been cutting fantastically since (thanks Mike!).
the prompt said my message was too short so I am typing this to lengthen it.
First my messages are "too long" (PM prompt)
Now they are "too short" (this message).
This posting stuff is nerve racking.
Sharpening is Facetating.Good enough is good enoughButBetter is Better.