Page 1 of 2 12 LastLast
Results 1 to 15 of 23

Thread: EZCAD/ FIBER INPUTS OUTPUTS settings

  1. 08-16-2016, 3:15 PM #1
    Martin Safranek
    Martin Safranek is offline [OP] Contributor
    Join Date
    Dec 2011
    Location
    Czech republic
    Posts
    73

    EZCAD/ FIBER INPUTS OUTPUTS settings

    Hi all,

    any experience with TTL inputs/outputs on fiber controlers ? I have ezcad 2.7.6 raycus fiber and i want connect conveyor for engravings but i dont have idea how to do ... I need one output with TTL HIGH when laser marking and one input start marking ....

    Thanks you for hints.

    Martin
    Last edited by Martin Safranek; 08-16-2016 at 3:17 PM.
    GCC Spirit LS 20w,60W, 100w
    WEIKE LC 1612 90/130W RECI
    Morntech Fiber 30w raycus
    Haotian Laser Fiber MOPA 80w
    CO2 Galvo 35w
    Corel X6
    Reply With Quote Reply With Quote
  3. 08-16-2016, 3:21 PM #2
    Gary Hair
    Gary Hair is offline Contributor
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,686
    What controller do you have Martin? The new one I put in my older machine has lots of input/output and they just need to be connected and configured in the software. I used one on my newest machine to control the red dot, it was on all the time and I only wanted it on when I clicked on the light button. It was easy to do, only required disassembly of the connector and soldering in a wire.
    Reply With Quote Reply With Quote
  4. 08-16-2016, 3:43 PM #3
    Martin Safranek
    Martin Safranek is offline [OP] Contributor
    Join Date
    Dec 2011
    Location
    Czech republic
    Posts
    73
    Hi Gary,

    its hard to say ... Im ask morntech and no reply ... Problem is that on controler is only label MODEL:IPG FIBER it seems thats may be clone of BJCZ ... Problem is that i dont understand princiles how to use I/O ... I know that port CON4 db15 female is probably used for IO ... i have already pin 9 connected and when i in config Param/port/ set port/pin 9 for function laser marking HIGH and start marking on pin 9 is 0V and i dont understand why .... Its reason of my thread ....

    Thank you .

    Martin

    IMG_0637.JPG
    Last edited by Martin Safranek; 08-16-2016 at 3:45 PM. Reason: add photo
    GCC Spirit LS 20w,60W, 100w
    WEIKE LC 1612 90/130W RECI
    Morntech Fiber 30w raycus
    Haotian Laser Fiber MOPA 80w
    CO2 Galvo 35w
    Corel X6
    Reply With Quote Reply With Quote
  5. 08-16-2016, 5:07 PM #4
    Martin Safranek
    Martin Safranek is offline [OP] Contributor
    Join Date
    Dec 2011
    Location
    Czech republic
    Posts
    73
    Gary,
    please can you describe what you did HW and SW changes in system for red dot control ? I hope that your example will help me lot.

    Thank you very much.

    Martin
    GCC Spirit LS 20w,60W, 100w
    WEIKE LC 1612 90/130W RECI
    Morntech Fiber 30w raycus
    Haotian Laser Fiber MOPA 80w
    CO2 Galvo 35w
    Corel X6
    Reply With Quote Reply With Quote
  6. 08-16-2016, 5:39 PM #5
    Gary Hair
    Gary Hair is offline Contributor
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,686
    The attached pdf should give you an idea of the pinouts. I don't think it's the exact board but they all seem to be about the same. Be very careful, connecting to the wrong pin can fry your board! I don't have the fiber computer running at the moment so I can't tell you where the setup is but it should be fairly easy to find.
    Attached Files Attached Files
    Reply With Quote Reply With Quote
  7. 08-16-2016, 6:49 PM #6
    Kev Williams's Avatar
    Kev Williams
    Kev Williams is offline Contributor
    Join Date
    Oct 2013
    Posts
    7,393
    Gar, your pdf thinks it's a Corel file, that thinks it's an html file...
    ========================================
    ELEVEN - rotary cutter tool machines
    FOUR - CO2 lasers
    THREE- make that FOUR now - fiber lasers
    ONE - vinyl cutter
    CASmate, Corel, Gravostyle

    Reply With Quote Reply With Quote
  8. 08-16-2016, 8:18 PM #7
    Gary Hair
    Gary Hair is offline Contributor
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,686
    Quote Originally Posted by Kev Williams View Post
    Gar, your pdf thinks it's a Corel file, that thinks it's an html file...
    I think your computer is smoking crack... I just downloaded it and unzipped it just fine.
    Reply With Quote Reply With Quote
  9. 08-16-2016, 11:14 PM #8
    Kev Williams's Avatar
    Kev Williams
    Kev Williams is offline Contributor
    Join Date
    Oct 2013
    Posts
    7,393
    Yup, I think you're right...

    My computer is seeing it as a Corel file, and is trying to open it in Corel, which says it can't open it...
    I tried to open it with IE, it gives me 10000 pages of scrambled letters.
    I tried to open it with PDF reader, it says it's corrupt..
    I tried Open Office reader, it says it's corrupt...

    No matter what I tried, NO where does "extract all" show up...

    Yet another reason I love Win8 so much...

    whaddya bet any of my XP computers will have no problem with it?

    Hmmm... Gar, have you tried downloading from a different computer? On XP it defaults to open with Firefox, which does the same thing as IE. If I force PDF reader to open it, it says it's not the right filetype or is corrupt...

    Neither of these 2 computers of mine offer to unzip it...
    Last edited by Kev Williams; 08-16-2016 at 11:20 PM.
    ========================================
    ELEVEN - rotary cutter tool machines
    FOUR - CO2 lasers
    THREE- make that FOUR now - fiber lasers
    ONE - vinyl cutter
    CASmate, Corel, Gravostyle

    Reply With Quote Reply With Quote
  10. 08-17-2016, 12:16 AM #9
    Gary Hair
    Gary Hair is offline Contributor
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,686
    From any of my 4 computers I click in it and chrome downloads it, that's it. I can then navigate to it and decide what to do with it. Windows 10 has a built-in zip/unzip app so I just double click on it and drag the file where I want it. easy as can be! darn that Windows 10...
    Reply With Quote Reply With Quote
  11. 08-17-2016, 2:27 PM #10
    Martin Safranek
    Martin Safranek is offline [OP] Contributor
    Join Date
    Dec 2011
    Location
    Czech republic
    Posts
    73
    Gary,

    i still dont have documentation for my control board ...my port wiring is bit different from yours. Please can you tell me more about ports numbers in ezcad setting ? Is pin number equal port number in config because from your manual it seems not ?

    Thank you.

    Martin
    GCC Spirit LS 20w,60W, 100w
    WEIKE LC 1612 90/130W RECI
    Morntech Fiber 30w raycus
    Haotian Laser Fiber MOPA 80w
    CO2 Galvo 35w
    Corel X6
    Reply With Quote Reply With Quote
  12. 08-17-2016, 3:00 PM #11
    Gary Hair
    Gary Hair is offline Contributor
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,686
    Go here and see if you can find your manual, it almost has to be one of theirs. http://en.bjjcz.com/zxxz.html If you can't find it then contact their tech support, they should be able to tell you what it is if you send them a picture.

    The pic shows port settings, they can go to any pin selected in a drop-down box.
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  13. 08-21-2016, 10:35 AM #12
    Martin Safranek
    Martin Safranek is offline [OP] Contributor
    Join Date
    Dec 2011
    Location
    Czech republic
    Posts
    73
    SOLVED i used pin 8 CON4 against GND for start marking and pin 19 CON2 laser ON like reference for conveyor that laser marking. Unfortunately i wasnt able gain model of control board from aftersales support.
    Gary thank you for your hints.

    Martin
    GCC Spirit LS 20w,60W, 100w
    WEIKE LC 1612 90/130W RECI
    Morntech Fiber 30w raycus
    Haotian Laser Fiber MOPA 80w
    CO2 Galvo 35w
    Corel X6
    Reply With Quote Reply With Quote
  14. 08-21-2016, 1:49 PM #13
    Gary Hair
    Gary Hair is offline Contributor
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,686
    Quote Originally Posted by Martin Safranek View Post
    SOLVED i used pin 8 CON4 against GND for start marking and pin 19 CON2 laser ON like reference for conveyor that laser marking. Unfortunately i wasnt able gain model of control board from aftersales support.
    Gary thank you for your hints.

    Martin
    Glad you got it working Martin! Now we all need to see a video of how it all works.
    Reply With Quote Reply With Quote
  15. 10-05-2016, 7:39 AM #14
    Martin Safranek
    Martin Safranek is offline [OP] Contributor
    Join Date
    Dec 2011
    Location
    Czech republic
    Posts
    73
    Hi Gary,

    im sorry for delay .. here is short video ....

    https://goo.gl/photos/xwQeNgqXQCa2dvNZA

    Martin
    GCC Spirit LS 20w,60W, 100w
    WEIKE LC 1612 90/130W RECI
    Morntech Fiber 30w raycus
    Haotian Laser Fiber MOPA 80w
    CO2 Galvo 35w
    Corel X6
    Reply With Quote Reply With Quote
  16. 10-05-2016, 8:28 AM #15
    Bill George's Avatar
    Bill George
    Bill George is offline Contributor
    Join Date
    Mar 2014
    Location
    Iowa USA
    Posts
    4,480
    Nice job of automation.
    Retired Guy- Central Iowa.HVAC/R , Cloudray Galvo Fiber , -Windows 10
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules