Page 2 of 2 FirstFirst 12
Results 16 to 26 of 26

Thread: How to remove mold from vinyl siding?

  1. #16
    Join Date
    Aug 2013
    Location
    Hatfield, AR
    Posts
    1,170
    We use vinegar/mr clean mix and a sponge mop then rinse with a hose. We can't use bleach because of the flower beds. We have to do this every two years to the north face of our home.
    -Lud

  2. #17
    Join Date
    Mar 2003
    Location
    Monroe, MI
    Posts
    11,896
    I've not had any luck with any of the big box products unless some mechanical agitation was used. Doesn't take much. A brush like Lee posted on a painters pole will get you pretty far off the ground but might not work on a 2 story house if you've got it higher up. Luckily around here it seems to mostly form in the bottom 6-10'. I assume the air is less humid and there's more circulation higher up.

    I pretty much can't be around bleach (I start coughing badly) so I've never tried that but I'd be real careful where any overspray goes.


  3. #18
    Google "soft wash power-washing." If you dig deep enough, you will find several recipes. The one I use, go to Home Depot, and in the swimming pool section, you will see the pool bleach. It is 11% concentrate, vs the 4% Clorox. Mix it 50-50 with water, and add a cup of Dawn to help it stick to the siding. Spray it on, let it sit for app. 5 minutes. On my vinyl siding, it made the siding look new. It also cleaned the facia and soffit very well. I spray it on with my power-washer with a low pressure nozzle, but using a pump sprayer would be just as efficient. I agree with the above comment about not using high pressure on vinyl siding.

  4. #19

    Painted gutter cleaning

    I’d never satisfactorily cleaned painted aluminum gutters until someone recommended Simple Green®. Give it a try if you’re not happy with results using bleach or other detergents.


  5. #20
    Look on Amazon for a product called "X14". Don't even bother with the bleach/vinegar/baking soda/whatever - X14 is what you want, and will solve your problem instantly.

  6. #21
    Join Date
    Dec 2012
    Location
    Bedford, NH
    Posts
    1,286
    I also use the Hudson Self-Mixing Hose End Sprayer as Bob Vavricka mentioned above. It's really does work well, providing the cleaning media isn't too thick to begin with. It's very convenient not having to pre-mix the solution.

    I also use this sprayer to spray along the foundation of my home each year to protect against, or kill off, carpenter ants, termites, or other insects as well. It's a handy tool to have.
    Thoughts entering one's mind need not exit one's mouth!
    As I age my memory fades .... and that's a load off my mind!

    "We Live In The Land Of The Free, Only Because Of The Brave"
    “The problems we face today are there because the people who work for a living are outnumbered by those who vote for a living."
    "
    Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery." Winston Churchill

  7. #22
    Join Date
    Apr 2007
    Location
    Columbus, Ohio, USA
    Posts
    3,441
    I have had good luck with this:

    https://www.amazon.com/dp/B001N7RZC0

    Mold Armor for your house.

    My experience is that it also depends on how long it has been there. If this has been there for a few years, you need to scrub it. If it is relatively new, give this stuff a go. Well, it helps regardless. What I like is that you can spray, wait, then rinse off.

    It is not expensive and it is easy to use. i would for sure try this before paying someone to come out. Keep the container in case you want to try mixing up your own solutions with vinegar (or whatever.... and I am not recommending for or against vinegar, but someone did mention using it).

  8. #23
    Join Date
    Sep 2006
    Location
    Deep South
    Posts
    3,970
    I believe EZ House Wash was the other product I mentioned in #7 the name of which I couldn't remember.

  9. #24
    Join Date
    Apr 2007
    Location
    New Jersey
    Posts
    1,347
    Blog Entries
    1

    I decided to have the house power washed

    I looked over the house more carefully and noticed that the soffits were pretty dirty (it's a 3 story house so the soffits are very high) so I decided to get the whole house power washed.
    Thanks for all your suggestions
    Dennis

  10. #25
    Join Date
    Mar 2003
    Location
    SE PA - Central Bucks County
    Posts
    65,685
    Quote Originally Posted by dennis thompson View Post
    I looked over the house more carefully and noticed that the soffits were pretty dirty (it's a 3 story house so the soffits are very high) so I decided to get the whole house power washed.
    Thanks for all your suggestions
    Our neighbor, who is selling their home to downsize, just had that done. Wow...what a difference!
    --

    The most expensive tool is the one you buy "cheaply" and often...

  11. #26
    Join Date
    Sep 2006
    Location
    Henderson Kentucky
    Posts
    1,498
    Blog Entries
    2
    Quote Originally Posted by dennis thompson View Post
    The vinyl siding on the front of my house has some green mold on it. It is pretty high and I no longer use ladders more than six feet high. Before I hire someone to pressure wash it I thought I'd try to use one of those siding cleaners that you attach to your hose. Obviously I would just spray it on and rinse it off, the height would not allow me to scrub it. Has anyone ever used one of these cleaners with any success and,if so, which one did you use?
    Thanks
    I just did my whole house. I use liquid Spic and Span mixed in a five gallon bucket. A soft bristle brush on an extension pole works great. I pre wet with hose and do an area with the solution and brush then rinse. Move on to the next section.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •