Originally Posted by
Jeff Farris
Dennis, let me preface this response by acknowledging that I make my living selling TORMEK sharpening systems. Your thread seems like the best opportunity to put the cards on the table about how the Scheppach copy cat machine stacks up to the TORMEK.
Scheppach approached us at the IWF in Atlanta in 2004, trying to lure us away from TORMEK demonstration with the promise of an equal product at a better price. Now, I have been working against price objections for 13 years, and the idea of having a price advantage for once, certainly had some appeal. However, the old saying, "You get what you pay for" could not be more appropriate when you critically compare the two systems. Which I did before telling Scheppach, "No thanks".
First let's examine the stone size and potential life. A little background for the US readers is in order first. In Europe, TORMEK sells two machines. The Model 2000 is exactly like the Model 2000 sold here in the USA - 250mm grindstone and 200mm honing wheel. The Model 1200 has a 200mm grindstone and a 145mm honing wheel. The most important point to note is that the frames are completely different designs. The 1200 is not sold in the USA for several reasons. Chief among them is the fact that by the time you rewire the motor for 110VAC 60Hz power, and ship them 4,000 miles, the price difference shrinks to the point that the 1200 loses all its appeal.
When Scheppach copied the TORMEK, they decided to offer two versions, as well. But, they are using the same frame for both large and small diameter systems. If they were offering the 250mm system in the USA, the price difference between a Sceppach and TORMEK would be so insignificant that no one would bite. So, they are selling their 200mm version here. By putting a 200mm grindstone on a frame designed for a 250mm grindstone, you greatly limit the amount of stone that can be used before you start having interference from other parts of the machine. To quantify this, it is 3-3/4" from the surface of a new TORMEK stone to the frame. It is 1-5/16" from the surface of a new Scheppach stone to the frame. Many people view the difference between the 10 inch TORMEK and 8 inch Scheppach stones as insignificant. But, when you actually look at the frames and their relationship to the stones, it becomes apparent that TORMEK offers nearly three times more usable stone! The grindstone is also 20% narrower (40mm compared to 50mm) That means that the surface is going to be working harder and breaking down quicker, thus contributing to the problem outlined above.
As far as their stone being better suited to HSS, I won't call anyone to prove that, because I truly doubt anyone who has first hand knowledge of the stone's design or manufacture could be reached by this forum to justify that statement. In my understanding of bonded abrasives, if they're saying that the stone cuts HSS faster than the TORMEK, then the stone will wear faster than the TORMEK stone, too. To cut faster, you have to have a more open grain structure, and that means faster wear. The converse of this is that the grading system, which Scheppach has also tried to copy, is most effective at exactly the grain size, bonding density, and porosity of the TORMEK grindstone. See Fine Woodworking's article this month. Tim Albers found that the Scheppach grindstone, when graded, left significantly heavier scratches than the TORMEK grindstone.
A less obvious, but very functional difference between the two grindstones is the lack of the recessed center found on the TORMEK stone. The recessed center lets you use the side of the stone to lap the backs of tool without depositing dross on the machine axle or wadding up the label. The raised surface can also be refinished and maintained flat. While a stone without the recess can be used a few times for lapping, eventually the surface will start showing more wear on the outside, and cannot be flattened.
With regard to power: One of TORMEK's original patents was their unique drive system. Scheppach has done a very poor job of copying the design. Hundreds of thousands of woodworkers -- many of them contributors here on SMC -- have watched me put the vast majority of my 240 pound weight against the grindstone of a TORMEK while it is running. I can stop a Scheppach with two fingers.
The TORMEK Universal Tool Support has included a micro-adjuster for the last couple of years. That feature has been awarded a design patent, so you won't see it on the Scheppach until the patent expires and they can copy that, too.
Scheppach copied the original AngleMaster, which TORMEK replaced 6 or 7 years ago. Instead of 4 pre-set angles that are only accurate when the stone is full-sized, the new Pro AngleMaster compensates for changes in stone diameter and allows you to accurately set any angle between 15 and 75 degrees.
A TORMEK comes with a hardcover Owner's Handbook with over 500 illustrations and step-by-step instructions. It also has a 23 minute video and a toll free number where you can get personalized help, if you need it. The Scheppach comes with a few pages of typewritten text that has been photocopied.
Three times more usable stone, vastly greater power delivery, true dual grit function, lapping for the life of the stone, micro-adjuster for angle adjustment, versatile and accurate angle setting, and outstanding documentation and technical support. Not opinion, fact.
TORMEK pioneered water-cooled sharpening. They recognize that competition is inevitable. That is why they are constantly working to update, upgrade and improve the system. It is admirable that every improvement that has been introduced can be retrofitted to machines built 20 years ago. Personally, I would have more respect for Scheppach if their copy had even one design modification that could be viewed as an advantage or improvement. As it is, I just can't see how anyone could carefully compare the two systems and decide that saving one Franklin would be worth what you give up by choosing the Scheppach.