Results 1 to 8 of 8

Thread: The Orange Block Plane – a review

  1. #1
    Join Date
    Feb 2004
    Location
    Perth, Australia
    Posts
    9,469

    The Orange Block Plane – a review

    <B>The Orange Block Plane – a review</B>

    After paring chisels and spokeshaves, my favourite tool is a block plane. These tools all have in common “feel”, a more direct involvement with the wood.

    My block plane collection of regular users centres on four planes, Stanleys #18 Knuckle joint (62 degree cutting angle) and #65 Knuckle joint (37 degree cutting angle), and Lie Nielsens #60 ˝ (37 degree cutting angle) and bronze #103 (45 degree cutting angle).

    The #18 is used as a small smoother for difficult face grain. The #65 (with a Hock blade) is probably the best performer of the lot. However, it is quite a large block plane and the LN #60 ˝ is more comfortable in the hand. The little #103 is the one I grab first when I work away from the bench. Its small size disguises a plane with the heft of something significantly larger. It does lack the ultimate performance of its bigger sibling owing to having a larger mouth.

    I was asked to review The Orange Block Plane by my son, Jamie, who has owned it since it was discovered in the bargain bin of Bunnings (the local borg) several years ago. At the time I felt that the $5 asking price was daylight robbery. Still, it does have some novel features, and I shall come to these in due course.

    I had not used this plane in some years. It had originally been purchased for Jamie (then 6 years old) to practice on in the workshop. He stored it amongst his treasures at the back of his wardrobe under a pile of old socks. He is now 13 years old and was recently re-introduced to woodworking at high school by Ms Robinson. He seems keen.

    Who manufactures The Orange Block Plane? Who indeed? It has no markings at all. Perhaps, this is a deliberate ploy of Triton (who shares this colour scheme) to manipulate everyone into using their ‘tailed routers instead!

    Here is the collection of block planes mentioned above. See if you can spot The Orange Block Plane.

    <center> <div><img src="http://i13.photobucket.com/albums/a262/Derek50/Articles/The%20Orange%20Block%20Plane/1.jpg" border="0" alt="" /> <br /></center>

    And in case you had any difficulty, here is a close up:

    <center> <div><img src="http://i13.photobucket.com/albums/a262/Derek50/Articles/The%20Orange%20Block%20Plane/2.jpg" border="0" alt="" /> <br /></center>


    <B>Important features of TOBP (The Orange Block Plane)</B>

    · Pressed steel construction that is even more durable than Ductile Iron.
    · Bright orange colour will not get lost among the mess … uh work-in-progress of the average workbench. Here is a close up of the colour:

    <center> <div><img src="http://i13.photobucket.com/albums/a262/Derek50/Articles/The%20Orange%20Block%20Plane/3.jpg" border="0" alt="" /> <br /></center>

    · No moving parts to wear out.
    · Admittedly, a modification had to be made to the lever cap. The original black plastic knob broke after being subjected to a stress test (i.e. it was eaten by Rufus, the dog), and a steel bolt was used as a replacement. This has proved a very successful upgrade.
    · The lever cap screw now doubles as a hang hole.
    · Construction has been simplified so that it is possible to press all pieces out of the same piece of steel. Hopefully no one gets confused and sharpens up the wrong bit.

    <center> <div><img src="http://i13.photobucket.com/albums/a262/Derek50/Articles/The%20Orange%20Block%20Plane/4.jpg" border="0" alt="" /> <br /></center>

    · The absence of a bed for the blade is a brave new design. The blade hangs in the air at 20°.
    · There is a finger hole at the front for your finger. It is a single finger hole designed for a single finger.
    · The sole has been lapped to .00000001mm deviation across its length of 6 3/8”.
    · It has a blade. It is made out of steel. For the technical boffins amongst us, it is 1 5/8” wide and 5/64” (2mm) thick, or vice versa.
    · It also has a mouth – somewhat reminiscent of the Grand Canyon:

    <center> <div><img src="http://i13.photobucket.com/albums/a262/Derek50/Articles/The%20Orange%20Block%20Plane/5.jpg" border="0" alt="" /> <br /></center>

    · The edges are rounded (so that you do not cut yourself?).

    <B>Tuning up The Orange Block Plane</B>

    Surprisingly, the plane was not ready to go out of the box. It required tuning. The original bevel appeared to be honed at 45°. This was re-ground to 25° and I freehand sharpened it to 8000 grit.

    The back of the blade had a low area throughout its length and width, a lot like a Japanese blade. I’m sure it was on purpose. It was possible to flatten it at the important back edge of the bevel.

    I assumed that I lapped the sole all those years ago as it was flat against a straight edge. I made no effort to flatten it this time around.

    The blade was place on the rear of the mouth and the cap iron tightened down. Fine adjustment was made with a mallet. The large mouth was ignored and the blade projection was considered sufficient once fine shavings emerged.

    <B>Making Shavings</B>

    Planing of pine face grain was completed by Jamie. Here is his style:

    <center> <div><img src="http://i13.photobucket.com/albums/a262/Derek50/Articles/The%20Orange%20Block%20Plane/6.jpg" border="0" alt="" /> <br /></center>

    And here are the shavings he made:

    <center> <div><img src="http://i13.photobucket.com/albums/a262/Derek50/Articles/The%20Orange%20Block%20Plane/7.jpg" border="0" alt="" /> <br /></center>

    A little later I attempted to cut pine endgrain:

    <center> <div><img src="http://i13.photobucket.com/albums/a262/Derek50/Articles/The%20Orange%20Block%20Plane/8.jpg" border="0" alt="" /> <br /></center>

    The resultant surface was actually pretty good. Pine end grain actually has a high rating on the difficulty scale. The soft wood fibres do not “stand up” to be cut, and a clean slice is a good measure of the blades ability to penetrate these fibres. What we would call “sharp” is really a combination of the smoothness and the angle of the bevel. A lower cutting angle and a smoother bevel equate to easier penetration.

    <B>Summing up</B>

    One might assume that my regular block planes are in no danger of being replaced by The Orange Block Plane, but this is not certain. The Orange Block Planet does give them a run for their money under these conditions (I did do some planing with the #65 and #60 ˝, and they really did not produce any better results on this piece of pine).

    The Orange Block Plane is really more than just a paperweight. It is probably one of the more “distinctive” planes I have used – indeed the colour causes me to be transfixed like a kangaroo in the headlights of my ute* on a dark night – I reckon that it would look pretty sharp in a belt holster made from a converted neoprene stubby holder**.

    There is definitely something machismo about this plane. One could saunter into the pub, lean against the bar, and attract admiring glances as you casually toss it onto the counter. It says “I am not affected by fashion … (I am cheap).” And to the kids, “One day this could be yours if you are good … (because I am cheap)”.

    Well that’s about it. You were expecting more? For $5? Yeah … right.


    Derek Cohen
    Perth, 2006

    * Utility vehicle (open bed truck)
    ** Beer holder

  2. #2
    Join Date
    Feb 2004
    Location
    Modesto, CA
    Posts
    2,364
    Derek...?...uummmm......Mr. Cohen...?........

    YOU DA MAN!!!

    (In case you're not familiar with that phrase, it's popular here in the States, probably more here in California than elsewhere, that means you're very good. In this case in the Dad area, the teacher area and the prose area.)

    Just goes to show that if one has the knowledge and experience, then the cost of, or materials in, the tool doesn't make quite as much of a defference. Wll done.


    Mark Rios

    Anything worth taking seriously is worth making fun of.

    "All roads lead to a terrestrial planet finder telescope"

    We arrive at this moment...by the unswerving punctuality...of chance.

  3. #3
    Join Date
    Dec 2005
    Location
    Northern Virginia
    Posts
    243
    Derek, quite impressive, I have got to get one of those. But tell me, is that authentic orange japanning, or is it imitation?

    I think the glove box of your car would be the best place for this plane - you could use it as a tire chock when changing a flat, a signalling device to warn other vehicles, an emergency window breaker if you become trapped, you could plane down high spots on your tires - the possible uses are endless.

    Just great, you made my night while traveling...

    Maurice

  4. #4
    I love that priceless eye bolt sticking out of the top............

    Cheap planes work pretty good if you put in the work to flatten the sole and sharpen the blade (to the correct angle)..........

  5. #5
    Join Date
    Mar 2003
    Location
    SE PA - Central Bucks County
    Posts
    65,688
    The plane is nice. (It would go very well with Robert Tarr's custom orange powdercoat Adjust-A-Bench) The narrative was grand! Thanks for sharing, Derek!!
    --

    The most expensive tool is the one you buy "cheaply" and often...

  6. #6
    Lol. Nice write up!!

    I've got one similar, a dark red one.


  7. #7
    Join Date
    Jul 2004
    Location
    Carlyle IL
    Posts
    2,183
    I suppose in many instances that real flat steel is really flat steel and really sharp is really sharp no matter what one pays for the tool!

    Joe

  8. #8
    Join Date
    Dec 2004
    Location
    St. Louis
    Posts
    3,349
    Derek, please repost with additional pictures, as I could not determine which of the block planes you were referring to. Perhaps if you added arrows and circles?

    My wife was looking over my shoulder as I read your post and commented that the plane was close to Tennessee Vols color. Not Gator orange - which I would prefer.

    We've talked about flying down that way to do some diving some day. My hope is that she doesn't make me stop at a Bunnings to pick one up. My son will be 6 next week, so I hope I can hold her off for a while.

    Thanks for another well written review.

    Now get moving on a review of those upscale LV planes people keep talking about.
    Where did I put that tape measure...

Similar Threads

  1. Mini Plane review, Mujingfang Smoother??
    By Gene Collison in forum Neanderthal Haven
    Replies: 17
    Last Post: 02-11-2012, 5:59 PM
  2. Low or Standard Angle Block Plane
    By Todd Franks in forum Neanderthal Haven
    Replies: 8
    Last Post: 12-25-2005, 1:45 PM
  3. Block Plane shop solution
    By Neil Bosdet in forum General Woodworking and Power Tools
    Replies: 3
    Last Post: 11-25-2005, 4:50 PM
  4. Veritas Medium Shoulder Plane Reviewed
    By Brad Olson in forum Neanderthal Haven
    Replies: 4
    Last Post: 12-07-2004, 4:04 PM
  5. Woodcraft Rosewood Plow Plane review (long)
    By Marc Hills in forum Neanderthal Haven
    Replies: 2
    Last Post: 04-06-2004, 11:59 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •