Results 1 to 4 of 4

Thread: tool usage(long and funny)

  1. #1
    Join Date
    Feb 2003
    Location
    Waterbury Connecticut
    Posts
    61

    tool usage(long and funny)

    Caught this on an Australian ww board and had to share. Some things are universal..enjoy
    With thanks to: Stephen Meddings Australia
    HAMMER:
    Originally employed as a weapon of war, the hammer nowadays is used as a kind of divining rod to locate expensive parts not far from the object we are trying to hit.

    MECHANIC'S KNIFE:
    Used to open and slice through the contents of cardboard cartons delivered to your front door; works particularly well on boxes containing seats and motorcycle jackets.

    ELECTRIC HAND DRILL:
    Normally used for spinning steel Pop rivets in their holes until you die of old age, but it also works great for drilling mounting holes in fenders just above the brake line that goes to the rear wheel.

    PLIERS:
    Used to round off bolt heads.

    HACKSAW:
    One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence it's course, the more dismal your future becomes.

    VISE-GRIPS:
    Used to round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand.

    OXYACETYLENE TORCH:
    Used almost entirely for setting various flammable objects in your garage on fire. Also handy for igniting the grease inside a brake drum you're trying to get the bearing race out of.

    WHITWORTH SOCKETS:
    Once used for working on older British cars and motorcycles, they are now used mainly for impersonating that 9/16 or 1/2 inch socket you've been searching for for the last 15 minutes.

    DRILL PRESS:
    A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, splattering it against that freshly painted part you were drying.

    WIRE WHEEL:
    Cleans rust off old bolts and then throws them somewhere under the workbench with the speed of light. Also removes fingerprint whorls and hard-earned guitar calluses in about the time it takes you to say "Ouch...."

    HYDRAULIC FLOOR JACK:
    Used for lowering a motorcycle to the ground after you have installed your new front disk brake setup, trapping the jack handle firmly under the front fender.

    EIGHT-FOOT LONG DOUGLAS FIR 2X4:
    Used for levering a motorcycle upward off a hydraulic jack.

    TWEEZERS:
    A tool for removing wood splinters.

    PHONE:
    Tool for calling your neighbor to see if he has another hydraulic floor jack.

    GASKET SCRAPER:
    Theoretically useful as a sandwich tool for spreading mayonnaise; used mainly for getting dog-doo off your boot.

    BOLT AND STUD EXTRACTOR:
    A tool that snaps off in bolt holes and is ten times harder than any known drill bit.

    TIMING LIGHT:
    A stroboscopic instrument for illuminating grease buildup.

    TWO-TON HYDRAULIC ENGINE HOIST:
    A handy tool for testing the tensile strength of ground straps and brake lines you may have forgotten to disconnect.

    1/2" x 16"-INCH SCREWDRIVER:
    A large motor mount prying tool that inexplicably has an accurately machined screwdriver tip on the end without the handle.

    BATTERY ELECTROLYTE TESTER:
    A handy tool for transferring sulfuric acid from a car battery to the inside of your toolbox after determining that your battery is dead as a doornail, just as you thought.

    AVIATION METAL SNIPS:
    See hacksaw.

    TROUBLE LIGHT:
    The mechanic's own tanning booth. Sometimes called a drop light, it is a good source of vitamin D, "the sunshine vitamin", which is not otherwise found under motorcycles at night. Health benefits aside, its main purpose is to consume 40-watt light bulbs at about the same rate that 105-mm Howitzer shells might be used during, say, the first few hours of the Battles of the Bulge. More often dark than light, it's name is some-what misleading.

    PHILLIPS SCREWDRIVER:
    Normally used to stab the lids of old-style paper-and-tin oil cans and splash oil on your shirt; can also be used, as name implies, to round off Phillips screw heads.

    AIR COMPRESSOR:
    A machine that takes energy produced in a coal-burning power plant 200 miles away and transforms it into compressed air that travels by hose to a pneumatic impact wrench that grips rusty bolts last tightened 60 years ago by someone and rounds them off.

    PRY BAR:
    A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part.

    HOSE CUTTER:
    A tool used to cut hoses 1/2 inch too short.

    now let me clean the coffee off the keyboard

    walt q
    There's no tool like an old tool

  2. #2
    Thanks Walt, I needed a laugh after the morning I had at work. Whew what a day.
    Wisdom comes with age, but sometimes age comes alone.
    Don

  3. #3
    Join Date
    Feb 2003
    Location
    Coatesville, PA
    Posts
    958

    Thanks Walt

    Brought back many funny memories from my days wrenching on cars & motorcycles

    Not that any of that kind of stuff happened to me mind you - it was other guys I knew at the time
    God Bless America!

    Tom Sweeney BP

  4. #4
    Join Date
    Feb 2003
    Location
    Lafayette, IN
    Posts
    4,563
    You went ahead and made my day.
    Jason

    "Don't get stuck on stupid." --Lt. Gen. Russel Honore


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •