Results 1 to 9 of 9

Thread: Truing up cupped boards without joiner

  1. #1
    Join Date
    Nov 2006
    Location
    Sterling Heights Michigan
    Posts
    186

    Truing up cupped boards without joiner

    I have a delta 12" planner but only have a 4"joiner (craftsman).
    Can one true up a cupped piece of wood with just a planner?

  2. #2
    Folks will say no but heres what I do. I run it on the rails of the cup side until I get a nice wide flat spot on the back. At that point I flip it over and take out the rails and then keep flippng it until done. I've been doing it this way for many years.

    Bob

  3. #3
    Join Date
    Mar 2005
    Location
    Spokane, Washington
    Posts
    4,021
    The Feb 2005 issue of Fine Woodworking (#175) has an article on making a sled for a planer that will allow you to joint on a planer. There is also a video to go along with the article, but you have to be a member of their on line service to view it. You can join just for a month if you want, and download articles to your hearts content.

    Dan
    Eternity is an awfully long time, especially toward the end.

    -Woody Allen-

    Critiques on works posted are always welcome

  4. #4
    Join Date
    Mar 2006
    Location
    SoCal
    Posts
    22,492
    Blog Entries
    1
    I use a sled. Just a piece of particle board with a bunch of holes in it where I have placed short screws to support the wobble-points of the offending material and a block attached to the front so the planer draws the material and sled both through. Super simple. There's a picture of it in this thread:

    http://www.sawmillcreek.org/showthread.php?t=51308
    Last edited by glenn bradley; 02-15-2007 at 10:52 AM.
    "A hen is only an egg's way of making another egg".


    – Samuel Butler

  5. #5
    Quote Originally Posted by Dan Forman
    The Feb 2005 issue of Fine Woodworking (#175) has an article on making a sled for a planer that will allow you to joint on a planer. There is also a video to go along with the article, but you have to be a member of their on line service to view it. You can join just for a month if you want, and download articles to your hearts content.

    Dan
    I built that planer sled and have used it alot. However, it is big and heavy and I have had problems with the size.

    I have seen some other options that I plan on trying. One is taking a piece of particle board and hot-gluing shims and the board to be planned onto it and then sending it through. It should be lighter and hold the board better.

    You may want to search around for some other planner sled ideas, but the theory is sound its just how you carry it off.

    Scott

  6. #6
    Glenn, your sled looks like it could be worth a try. It looks a lot lighter then mine.

    Scott

  7. #7
    Join Date
    Mar 2006
    Location
    SoCal
    Posts
    22,492
    Blog Entries
    1
    Scott,

    Maybe just 'cause this one is short. I have a longer one and it does kinda get heavy. Usually the material will sit still if I compensate for the wobble well. If it is questionable, I'll use hot glue or double-stick tape. Once under the rollers, if supported well, the lumber doesn't want to go anywhere except through.
    "A hen is only an egg's way of making another egg".


    – Samuel Butler

  8. #8
    Join Date
    Mar 2005
    Location
    Spokane, Washington
    Posts
    4,021
    Don't overlook the fact that you can also use a handplane to flatten the face of a board enough to run it through the planer. Doesn't need to be perfect, just good enough, as the planer will take care of the rest when you filp the board and feed it through again.

    Dan
    Eternity is an awfully long time, especially toward the end.

    -Woody Allen-

    Critiques on works posted are always welcome

  9. #9
    Join Date
    Nov 2006
    Location
    Sterling Heights Michigan
    Posts
    186
    Thanks everyone for the info.
    Man I love this forum!

Similar Threads

  1. cupped boards fix?
    By Brian Knop in forum General Woodworking and Power Tools
    Replies: 9
    Last Post: 01-12-2006, 6:45 PM
  2. replacing t&g boards on front porch
    By fred woltersdorf in forum General Woodworking and Power Tools
    Replies: 6
    Last Post: 09-22-2005, 5:36 PM
  3. Newbie ? Flattening Boards with Benchtop Planer
    By David Degan in forum General Woodworking and Power Tools
    Replies: 10
    Last Post: 08-18-2005, 10:22 PM
  4. Flattening Maple Boards
    By Bob Winkler in forum General Woodworking and Power Tools
    Replies: 6
    Last Post: 02-18-2005, 1:23 PM
  5. shooting boards
    By Zahid Naqvi in forum Neanderthal Haven
    Replies: 4
    Last Post: 12-08-2004, 1:09 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •