Page 1 of 2 12 LastLast
Results 1 to 15 of 17

Thread: Jig to engraving spheres

  1. #1

    Jig to engraving spheres

    Has anyone set up a jig to engrave spheres using the rotary tool on an Epilog? I'm working on it and have a plan in mind, but am curious as to whether anyone else already has something that works.

    I have to engrave five wooden spheres ranging from 4" d to 1.25" d and will only be engarving around the 'equator', not all over the sphere. The engraving will not be continuous around the circumference, but there will be something on two opposing 'sides' of the equator. The opposing sides would not have to be engraved in one pass. I will be engraving some corporate logos. Most are from original vector art, one is from a JPG. There will also be some text and there will be one photo.

    Any thoughts or suggestions are welcomed. I will be happy to post my solution as soon as I try it out to see if it works.

    Paul Proffitt
    Epilog 24TT 45 Watt, Corel 12 and Illustrator CS

  2. #2
    Join Date
    Oct 2005
    Location
    Moreton, Wirral, UK
    Posts
    3,287
    Paul, this is an interesting one, spheres are sort of the dread of all laser engravers I think. If it were me, I would consider something on the lines of using a cardboard tube, like the ones that you get posters/calendars delivered in. Cut it in the middle and use rubberised glue that can easily be removed later. Glue or attach one on either side of the sphere but be able to hold the weight between the rollers on the rotary.
    Epilog 45w Helix X3/X5 Corel Microflame Generator (flame polisher) Heat Bender


  3. #3
    3" diameter dowels and double stick tape jump to mind.
    "I love the smell of sawdust in the morning".
    Robert Duval in "Apileachips Now". - almost.


    Laserpro Spirit 60W laser, Corel X3
    Missionfurnishings, Mitchell Andrus Studios, NC

  4. #4
    You will have to use something the same size as the sphere if you use a dowell type contraption. Anything smaller and the rotation will be off.

  5. #5
    Jody... good catch.
    "I love the smell of sawdust in the morning".
    Robert Duval in "Apileachips Now". - almost.


    Laserpro Spirit 60W laser, Corel X3
    Missionfurnishings, Mitchell Andrus Studios, NC

  6. #6
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,193
    Quote Originally Posted by Frank Corker
    Paul, this is an interesting one, spheres are sort of the dread of all laser engravers I think. If it were me, I would consider something on the lines of using a cardboard tube, like the ones that you get posters/calendars delivered in. Cut it in the middle and use rubberised glue that can easily be removed later. Glue or attach one on either side of the sphere but be able to hold the weight between the rollers on the rotary.
    How about PVC pipe instead of cardboard? It will be much stronger and less likely to flex. Cut it to length and use some self-stick foam or rubber to give you something to grip the spheres.

    Gary

  7. #7
    Join Date
    Aug 2006
    Location
    Lake Stevens, WA
    Posts
    467
    A length of PVC matching about half the diameter of the sphere would be a great way to hold them in place while engraving them.

  8. #8
    Join Date
    May 2004
    Location
    Vancouver, Washington
    Posts
    397
    Depending on the diameter, how about a square or a circle (or any shape) cut out of a 1/4" piece of material, acrylic, MDF... You just have to make the hole small enough so the sphere doesn't bottom out. To get away with a larger hole, stack/glue multiple layers.

    Shaddy

  9. #9
    Join Date
    Mar 2006
    Location
    Owego, NY
    Posts
    733
    You can compensate for the diameter of the dowel or tube by cutting a pair of discs of the same diameter as the sphere and glueing them to the outer end of the dowels or tubes. The discs then ride on the rollers of the rotary attachment.
    Dave Jones -- Epilog Mini-24, 45 watt, CorelDraw X3, Creative Suite CS2

  10. #10
    Join Date
    Feb 2003
    Location
    Hayes, Virginia
    Posts
    12,270
    Whatever style jig that is used will have to be aligned on both ends of the sphere perfectly or the sphere when rotated will wobble up and down. I would suggest a V-Trough be made to install the end pieces. Providing the sphere is three inches in diameter and the ends are the same the V-Trough should do the trick.

    .

  11. #11
    Join Date
    Aug 2006
    Location
    Lake Stevens, WA
    Posts
    467
    Cut two MDF disks that match the diameter of your rotary fixture heads and mount the pvc to that on dead center. They'll center easily and shouldn't wobble to any huge degree.

  12. #12
    I very much appreciate all the replies. Obviously a lot of experience in this forum. My intended approach, which is about to be tested, is to use PVC pipe couplings and adapters. The PVC pipe and adapters are relatively inexpensive, relatively accurate with respect to dimensional repeatability and stability and the adapters are made to fit into each other.

    I measured the drive wheel diameter including the o-ring as 2.62". A 2" PVC coupler is 2.728" od - same on all three I bought. By factoring in this difference in diameter if needed (see separate rotary tool post question) I can eliminate that difference as an issue. Then I can use some combination of a 2" to 1" adapter, a 1" to 1/2" adapter and a piece of 1/2" PVC pipe to handle the 4" to 1.25" diameter spheres. I would absolutely need to account for any difference between the diameter of the driven cylinder (the 2" PVC coupling) and the sphere and adjust my drawing's Y measurement accordingly.

    I'm planning to align the two ends by chucking the two 'jigs' in scroll chucks on my lathe - one on the headstock and one on the tailstock. If the headstock and tailstock are properly aligned then the jigs should be aligned once the entire object is placed on the rotary tool. More later on how I plan to hold the jigs on the object to be engraved. I'll be exploring double sided tape as well as small strips of inner tube stretched from one end to the other.

    More after I actually try it.

  13. #13
    Join Date
    Aug 2006
    Location
    Lake Stevens, WA
    Posts
    467
    I think I'm describing the Pinnacle / Laserpro rotary engravers. They can engrave pretty much anything you can clamp into them.

    I'm guess this is more about the roller-type attachments?

  14. #14
    Yes, this is about the roller type (referred to by Epilog as the rotary attachment) tool.

  15. #15
    Join Date
    Feb 2007
    Location
    Siloam, North Carolina
    Posts
    158
    Quote Originally Posted by Paul Proffitt

    More after I actually try it.
    Well, how did it turn out???

Similar Threads

  1. Engraving then cutting acrylic
    By Mike Klafehn in forum Laser Engraving General Topics
    Replies: 14
    Last Post: 01-05-2007, 3:46 PM
  2. Black Marble Engraving Secret Sauce
    By Keith Outten in forum Laser Engraving General Topics
    Replies: 17
    Last Post: 06-08-2006, 1:14 AM
  3. Engraving Mirrors
    By Keith Outten in forum Laser Engraving General Topics
    Replies: 10
    Last Post: 07-27-2005, 12:01 AM
  4. How much???
    By Richard Allen in forum Laser Engraving General Topics
    Replies: 4
    Last Post: 05-11-2004, 2:37 PM
  5. Turned Spheres
    By Dominic Greco in forum General Woodworking and Power Tools
    Replies: 16
    Last Post: 08-14-2003, 5:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •