Results 1 to 12 of 12

Thread: EPS File of Concorde

  1. #1
    Join Date
    Oct 2005
    Location
    Moreton, Wirral, UK
    Posts
    3,287

    EPS File of Concorde

    Does anyone have either an eps file of Concorde, preferrably dramatic, or a high quality photograph. I am hoping to be putting this on a mirror (with a bit of luck). I do have quite a few but the quality isn't really that great.

    PS Has to have the Brit flag on it, not the Frenchie's but I can do a bit of modification
    Epilog 45w Helix X3/X5 Corel Microflame Generator (flame polisher) Heat Bender


  2. #2
    Join Date
    Nov 2006
    Location
    Innisfil Ontario Canada
    Posts
    4,019
    Did you try looking for a .pdf file on their website Frank..
    just yanking your chain..ha..

  3. #3
    Not great but better than nothing.
    Last edited by Mike Null; 07-01-2007 at 10:37 AM.
    Mike Null

    St. Louis Laser, Inc.

    Trotec Speedy 300, 80 watt
    Gravograph IS400
    Woodworking shop CLTT and Laser Sublimation
    Dye Sublimation
    CorelDraw X5, X7

  4. #4
    Join Date
    Oct 2005
    Location
    Moreton, Wirral, UK
    Posts
    3,287
    Thanks Mike, strangely enough, that is one of the 3 eps files I have! I have one plan, side on and front on. Just not quite there. But I appreciate your help.

    Bill, I already tried that!
    Epilog 45w Helix X3/X5 Corel Microflame Generator (flame polisher) Heat Bender


  5. #5
    Join Date
    Jul 2004
    Location
    Victor, NY
    Posts
    1,288

    Concorde

    Hi Frank;
    Here's a couple in wmf but can be changed to EPS easily.
    Hope they help and will keep looking.
    Best regards;
    George
    LaserArts
    Attached Files Attached Files

  6. #6
    Join Date
    Oct 2005
    Location
    Moreton, Wirral, UK
    Posts
    3,287
    Thank you George and thanks to everyone who has had a look on my behalf. I have now found a superb photograph which I will use. I will post the result when I'm done!
    Epilog 45w Helix X3/X5 Corel Microflame Generator (flame polisher) Heat Bender


  7. #7
    Join Date
    Oct 2005
    Location
    Moreton, Wirral, UK
    Posts
    3,287
    Okay, this is how it ended up, there is a plastic covering over it which I didn't realise would cause as much problem photographing it as it has. (That is why there are two photos of the same job)

    I think it has turned out pretty nice - 24"x18", customer was 'Over the moon' with it.
    Attached Images Attached Images
    Epilog 45w Helix X3/X5 Corel Microflame Generator (flame polisher) Heat Bender


  8. #8
    Frank, that's beautiful.

    On mirror, you say?
    Mike Null

    St. Louis Laser, Inc.

    Trotec Speedy 300, 80 watt
    Gravograph IS400
    Woodworking shop CLTT and Laser Sublimation
    Dye Sublimation
    CorelDraw X5, X7

  9. #9
    Join Date
    Oct 2005
    Location
    Moreton, Wirral, UK
    Posts
    3,287
    Thanks Mike, yes it's a mirror.
    Epilog 45w Helix X3/X5 Corel Microflame Generator (flame polisher) Heat Bender


  10. #10
    Join Date
    Dec 2006
    Location
    Wenatchee, WA
    Posts
    178
    Frank you did an excellent job.

    What doe the inscription say? What did you end up charging for the job? I like the idea of a mirror in a picture frame I really hadn't tried that.
    Carol VanArnam Epilog Helix 60w, Corel 12, I like chocolate.....

  11. #11

    Mirror

    Do you always laser yours in Grayscale. If so what power /speed ect.
    Very Nice
    Gail Laporte

  12. #12
    Join Date
    Oct 2005
    Location
    Moreton, Wirral, UK
    Posts
    3,287
    I did charge for it, but it was more of a favour for a favour, so it was low at £75. The inscription is not really that important and is only a 'little ditty' to the individual it was being presented to. I always do my mirrors in the picture frame, it's a simple matter of removing the backing taking the mirror out, engraving it and dropping it back inside (hopefully in one piece!)

    Gail, I always use 8bit greyscale and do my stuff in Photograv, there is no real setting for mirror so I use Cherry wood settings. I engraved this one at 35 speed 100 power
    Last edited by Frank Corker; 03-12-2007 at 5:13 AM.
    Epilog 45w Helix X3/X5 Corel Microflame Generator (flame polisher) Heat Bender


Similar Threads

  1. How to import Illustrator file to CorelDraw?
    By Richard Rumancik in forum Laser Engraving General Topics
    Replies: 5
    Last Post: 02-25-2007, 8:50 PM
  2. Downloading .cdr file
    By Jerre Griffin in forum Forum Tech Support
    Replies: 1
    Last Post: 11-28-2006, 4:40 PM
  3. file cabinet drawer file dimensions
    By jack duren in forum General Woodworking and Power Tools
    Replies: 6
    Last Post: 04-30-2005, 1:06 PM
  4. Hanging file system?
    By Jamie Buxton in forum General Woodworking and Power Tools
    Replies: 2
    Last Post: 07-28-2004, 1:30 AM
  5. Files, Filing, Filling and Finishing…Metal
    By Bob Smalser in forum Neanderthal Haven
    Replies: 3
    Last Post: 03-14-2004, 8:48 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •