Results 1 to 7 of 7

Thread: Electrical question, solder on wire for 220v 30 amp

  1. #1
    Join Date
    Jun 2006
    Location
    Los Angeles
    Posts
    636

    Electrical question, solder on wire for 220v 30 amp

    I have some 10/3 stranded wire that I want to use. The strands are a bit annoying to work with. Is there a danger in tinnning the bare ends that I am going to put in to a plug or receptacle?

  2. #2
    Join Date
    Dec 2003
    Location
    SF Bay Area, CA
    Posts
    15,332
    Ben,

    If you use back-wired (not back-stabbed) receptacles, the #10 strand connects to them pretty easily. You'll pay a little more for these but the connection is very secure.

    I dunno, I did my whole garage rewiring in #10 stranded and I didn't think it was all that bad to work with...certainly better than #10 solid (and I had a little bit of that to deal with)!

    The general consensus on solder as I've gathered is that it isn't a very good idea due to the fact that it could be possibe for the area that was soldered to get hot enough for the solder to melt and flow...somewhere...somewhere possibly bad.
    Wood: a fickle medium....

    Did you know SMC is user supported? Please help.

  3. #3
    I solder wires frequently for a variety of reasons.
    Some are
    1.) I don't trust the wire nut to hold all those ground wires and don't have a crimp

    2.) I prefer the permanent connection (for whatever reason)

    3.) I want the a multi strand wire to join together and be stiffer.

    4.) It comports with my arbitrary notion of how I want things on that particular day.

    I don't think you have any down side at all.

  4. #4
    Join Date
    Feb 2003
    Location
    South Windsor, CT
    Posts
    3,304
    Quote Originally Posted by Cliff Rohrabacher View Post
    I solder wires frequently for a variety of reasons.
    Some are
    1.) I don't trust the wire nut to hold all those ground wires and don't have a crimp

    2.) I prefer the permanent connection (for whatever reason)

    3.) I want the a multi strand wire to join together and be stiffer.

    4.) It comports with my arbitrary notion of how I want things on that particular day.

    I don't think you have any down side at all.
    Cliff,

    Solder is not meant to be any part of the mechanical connection joining conductors - it's purely an electrical connection.

    If you're using the solder because the connection needs it to help hold the connectors together, then the connection isn't properly formed.

    Rob

  5. #5
    Join Date
    Jun 2006
    Location
    Los Angeles
    Posts
    636
    My only reason to tin the wires is to keep the strands together, the strands coming apart is giving me a bit of a problem.

  6. #6
    Join Date
    Dec 2003
    Location
    SF Bay Area, CA
    Posts
    15,332
    Quote Originally Posted by Rob Russell View Post
    Solder is not meant to be any part of the mechanical connection joining conductors - it's purely an electrical connection.
    Perhaps this is true in the electrician's world but it is very much a mechanical holder in the PCB (printed circuit board) world!
    Wood: a fickle medium....

    Did you know SMC is user supported? Please help.

  7. #7
    In the electronics industry, we tin the wires that go under a screw connection to keep the wire from "birdcaging." However, I have not done this on a wire nut, but doubt any harm could come of it. The wire goes from stranded to solid after tinnintg and solid wire is used in wire nuts, too.

    As far as reflowing the solder from heat of the connection, that should not happen unless something else has gone bad.

Similar Threads

  1. Comment, Electrical Question and a Gloat
    By Hal Flynt in forum General Woodworking and Power Tools
    Replies: 22
    Last Post: 10-23-2008, 2:29 AM
  2. Electrical question
    By Jason Morgan in forum General Woodworking and Power Tools
    Replies: 48
    Last Post: 10-03-2007, 11:35 PM
  3. Electrical Subpanel Feeder Wire
    By David Axmann in forum General Woodworking and Power Tools
    Replies: 7
    Last Post: 05-19-2007, 12:35 AM
  4. shop electrical question...
    By markus shaffer in forum General Woodworking and Power Tools
    Replies: 11
    Last Post: 07-26-2004, 7:58 AM
  5. Electrical question
    By Joe Bourbois in forum General Woodworking and Power Tools
    Replies: 7
    Last Post: 03-01-2004, 11:45 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •