Results 1 to 12 of 12

Thread: Riving Knife Thickness

  1. #1
    Join Date
    Dec 2007
    Location
    Shelton,CT
    Posts
    38

    Riving Knife Thickness

    I just picked up my Sawstop and noticed the riving knife is 2mm or .079 inches thick. I am only intend on running full kerf blades .125 and was wondering if Sawstop made a thicker riving knife or if it is even worthwhile pursuing. To me it just seems like it would be more efective if it was thicker.

    Thanks
    JP

  2. #2
    Join Date
    Nov 2004
    Location
    Belden, Mississippi
    Posts
    2,742

    I would be interested too..

    Though I don't have a riving knife on my Grizz, I've been wondering about the effective thickness for splitters, riving knives, etc.
    Bill
    On the other hand, I still have five fingers.

  3. #3
    Join Date
    Dec 2006
    Location
    Toronto Ontario
    Posts
    11,236
    Hi Jeremy, riving knives should be thicker than the saw plate, thinner than the tooth width.

    If your riving knife meets the above, you're OK, if not you need a different knife.

    Regards, Rod.

  4. #4
    Join Date
    Dec 2007
    Location
    Shelton,CT
    Posts
    38
    Rod-

    By no means doubting you but could you elaborate a little as to why that is?

    It also looks like I may look into fabbing my own thicker one out of stainless.

    Thanks,
    JP

  5. #5
    Join Date
    May 2006
    Location
    Poland
    Posts
    637
    Hi Jeremy

    What Rod said but "in colors"...well, black & white drawing....



    Regards
    niki

  6. #6
    Join Date
    Mar 2006
    Location
    SoCal
    Posts
    22,480
    Blog Entries
    1
    I would think a quick call to Steel City tech support would solve this. If you're
    OK, they can explain. If you need a different splitter, they will probably send it to you.
    "A hen is only an egg's way of making another egg".


    – Samuel Butler

  7. #7
    Join Date
    Oct 2007
    Location
    Dawson Creek, BC
    Posts
    1,033
    I dont know about other manuf, but I know Felder sells three diff thicknesses.

    brad

  8. #8
    Jeremy,

    My jury's still out and I make the darn things. I have sent out about 40 Push/Pull splitters with 1/6" (.06xx) aluminum blades. I make slits on the trailing edge to bend the blade a bit thicker, but I don't know if they are being used. I have rec'd no negative feedback. I have a couple out with double ends; you flip it over when changing from thin to full kerf blades. I do not have any feedback on these yet.

    Recently I've been sending out Bolt-On Ripping Knives (****S) which mimic a riving knife and are suitable for retrofit to a few saw models.
    I've been fashioning these knives from .080 aluminum, again with the slits in the trailing edge.

    It is my opinion that the most important roll a splitter plays is to "guard" the back of the spinning saw blade. Loose off-cuts are the leading candidates for kick backs and if the splitter blade prevents the saw blade from getting a good enough bite, it cannot launch.

    I would love to hear what you find out from Steel City. I have no formal training on this subject.

    Please do not solicit information regarding my products via this thread.

  9. #9
    Join Date
    Oct 2006
    Location
    Bloomington, IL
    Posts
    6,009
    I know the Shark Guard splitter for the Sawstop is slightly thicker. It is what I use.

  10. #10
    Join Date
    Dec 2006
    Location
    Atlanta , Ga.
    Posts
    3,970
    Ditto what Rod Sheridan and Niki said even though you will find most manufacturers (especially the U.S. ones that have just added riving knives) make them so both a thin keft and full kerf will fit. One that is smaller than kerf and larger than blade body is ideal as it slightly narrows the gap that can allow a touch of the dangerous rear rising teeth.

    That is ideal but... unless you grind your own you are probably going to get less than ideal from the manufacturer as they are most likely going to do one thin enough to use both TK and full kerfs as I mentioned.

    BTW.. I think someone made a mental mistake on saying to call Steel City on the matter. The OP has a Saw-stop which doesn't have anything to do with what thicknesses Saw-stop has available for their saw.

    Sarge..

  11. #11
    As I recall Sawstop gives you directions on correctly setting up the riving knife. Basically you set it up so that it's towards the inside of the blade kerf. It doesn't really matter the thickness being thinner than the blade as long as you have it properly set up as above.
    Last edited by Brian Penning; 10-20-2008 at 8:56 PM.

  12. #12
    Join Date
    Dec 2007
    Location
    Shelton,CT
    Posts
    38
    Thanks for all the info...and Nissim thanks for the picture.

    In asking Rod to explain I guess I was more interested in what the thickness of the plate had on things. I would think you needed to be slightly thinner than the teeth as that is what is going to "bite". To thick and it will bind...

    I may try making my own (I have access to a metal fab shop)

    Does Steel City sell a riving knife that would fit a Sawstop? I will certainly call and report back if they do.

    The riving knife on my saw is set up even with the left side of the blade. This seems to be the less important side to have the tolerance close as it is not the side we worry about kickback.

Similar Threads

  1. Report on the Makita knife sharpener
    By Tom Jones III in forum General Woodworking and Power Tools
    Replies: 27
    Last Post: 01-11-2020, 7:36 PM
  2. Jointer and planer knives setting jig.
    By Liem Tran in forum General Woodworking and Power Tools
    Replies: 31
    Last Post: 04-26-2010, 9:36 AM
  3. Riving Knife - 2008?
    By Greg Peterson in forum General Woodworking and Power Tools
    Replies: 5
    Last Post: 12-30-2007, 1:06 AM
  4. Anyone Heard about this new Jet TS with Riving Knife
    By John Hedges in forum General Woodworking and Power Tools
    Replies: 7
    Last Post: 06-20-2007, 3:09 PM
  5. PM2000 riving knife system
    By Chris Setter in forum General Woodworking and Power Tools
    Replies: 28
    Last Post: 11-15-2006, 9:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •