Page 1 of 2 12 LastLast
Results 1 to 15 of 24

Thread: What species wood is this?

  1. #1

    What species wood is this?

    Okay, pop quiz, hotshots. What species wood is this?

    It was cut from a farm near Bellevue, Iowa. The property owner didn't know what it was. I took it because it came free with a load of walnut and cherry, also from his farm.

    I've heard maybe white oak, but that doesn't seem right to me. I've tried The Encyclopedia of Wood, but I'm still not sure.

    The board at left in the first pic has been planed; the rest is rough sawn.
    Attached Images Attached Images

  2. #2
    Join Date
    Feb 2008
    Location
    Stanwood, WA
    Posts
    3,059
    Depending on your lighting it is ash.
    Dewey

    "Everything is better with Inlay or Marquetry!"


  3. #3
    Actually, ash in any light!
    David DeCristoforo

  4. #4
    I am probably a little too far east to make anything more than a guess, but I vote for elm.

    I have no idea what is common for Iowa except cornstalks, and I'm pretty sure that's not it!

    Looks like the growth rings are too wide for oak, indicating a faster growing tree, and it has that secondary grain that appears in elm sometimes.

    I looks like ash, but doesn't seem white enough.

  5. #5
    Geez, you can't get any better than that quick response!

    No flash in the first pics but 560 equivalent watts of CFLs.

    Here's a few WITH the camera flash.
    Attached Images Attached Images

  6. #6
    What about Chestnut?

  7. #7
    Quote Originally Posted by John Keeton View Post
    I looks like ash, but doesn't seem white enough.
    I agree, its a little too dark for ash. At least when compared to the ash I have. Could be just the lighting though.
    If at first you don't succeed, look in the trash for the instructions.





  8. #8
    It seems lighting could make this difficult for you. For comparison, here's the mystery wood next to cherry and walnut, respectively, no flash and flash.
    Attached Images Attached Images

  9. #9
    Join Date
    May 2006
    Location
    Central Florida
    Posts
    266
    I was thinking butternut, but then again what do I know?

  10. #10
    That's Hickorashelmnut...
    David DeCristoforo

  11. #11
    Join Date
    Feb 2008
    Location
    Northfield, Mn
    Posts
    1,227
    Quote Originally Posted by Mac Cambra View Post
    I was thinking butternut, but then again what do I know?

    That and ash were my two votes. Hard to tell with out seeing it in person.

  12. #12
    Join Date
    Apr 2004
    Location
    Seattle
    Posts
    672
    Could be butternut as Mac suggested. It would be softer and lighter in weight than the walnut with similar grain pattern. If it is hard stuff it is still a mistery. JCB

  13. #13
    Well I was thinking ash too, the grain is very ash like. But the photos with a flash seem to show kind of a pink-ish cast so that would seem to rule out ash.

    I also don't think it is elm, elm has a very obvious interlocked grain which is not visible in these photos, granted they are not really up close photos though.

    Does it have any smell, if you plan off a shaving do you get an aroma? Maybe that's another clue we can use.

    The best way to identify it is to take a very sharp block plane, clean up a bit of end grain, then go to hobbithouseinc and check everyone's suggestions against his woodpics there.

    Dan

  14. #14
    Join Date
    Dec 2007
    Location
    Richfield, WI
    Posts
    65
    I'm going to break with the pack and throw out a wild idea. How about red mulberry? Search for images on Google. Looks pretty good to me, but I haven't seen it in person.

  15. #15
    I say chestnut.
    Jack Briggs
    Briggs Guitars

Similar Threads

  1. Replies: 59
    Last Post: 08-17-2008, 9:54 AM
  2. Turners Glossary...?
    By Stu Ablett in Tokyo Japan in forum Turner's Forum
    Replies: 15
    Last Post: 05-21-2008, 1:39 PM
  3. Best information to learn the different species of wood?
    By Mike Heidrick in forum General Woodworking and Power Tools
    Replies: 5
    Last Post: 11-19-2007, 6:08 AM
  4. Identifying Wood Species
    By Jerry Bittner in forum General Woodworking and Power Tools
    Replies: 2
    Last Post: 01-03-2006, 7:14 PM
  5. Wood dust and lung cancer association
    By Kurt Voss in forum General Woodworking and Power Tools
    Replies: 2
    Last Post: 05-11-2005, 6:30 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •