Page 1 of 2 12 LastLast
Results 1 to 15 of 30

Thread: Couple new tools - and, a rare glimpse!

  1. #1
    Join Date
    Oct 2007
    Location
    Central KY
    Posts
    17,582

    Couple new tools - and, a rare glimpse!

    After getting some input from fellow creekers, I purchased a Packard 1.25" German (Continental) gouge, and also a Benjamin Best 2" spindle roughing gouge. Just thought I would show a couple pics.

    1.jpg

    My prior roughing has been done with my original Harbor Freight SRG, and while it works fine, one can not aggressively remove material with it. There just is not enough mass and width to permit that on a large squared off block. I really enjoyed roughing with this inexpensive big chunk of metal!! Much more comfortable, and much quicker. A caveat - it takes off wood in a hurry! I will need to get used to checking the status a little more often - nearly removed too much!

    The German gouge was very pleasant to use. I didn't change the 45* factory grind, but touched up the edge. It leaves a very smooth surface, and I felt it was easy to control. One can get a nice, sweeping curve shaping an end grain turning. However, it did not want to behave as well coming across the top (end grain) and felt like one could get a catch if not careful in that presentation. I will experiment with the grind some and perhaps see how it does with a little different profile on the nose. I think this is going to be a nice add on to the tool rack! After using this one for awhile, if it continues to perform as I think it will, I suspect I might end up with a 3/4".
    2.jpg 3.jpg

    And, now for that rare glimpse! For those of you that have visited my shop, or even noticed in various pics I have posted, this is an extremely rare sight - actual "stuff" on the ways of the lathe, and even on the floor!!

    4.jpg
    And, here is the real shame of it all - except for blowing the shavings off the lathe, I left this mess when I came in a few moments ago.

    I am sure I will regret revealing this, but sometimes confession is good for the soul. The sun shall not set tomorrow on this mess!!

  2. #2
    Join Date
    Jul 2010
    Location
    Sandia Park, NM
    Posts
    1,068
    Who are you and where is John Keeton????? Thanks for the review, very interesting the differences in shape.
    When you approach the lathe you have "the plan", after your first catch you have "the intent".- P. Harbeck

  3. #3
    Join Date
    Jan 2009
    Location
    sLower Delaware
    Posts
    5,464
    Those weren't green shavings were they?

  4. #4
    Join Date
    Jan 2009
    Location
    Southern California
    Posts
    736
    What mess are you talking about? Looks clean to me.
    [SIGPIC][/SIGPIC]
    Please see personal profile for website info.

  5. #5
    Join Date
    Apr 2007
    Location
    Ware Shoals , S.C.
    Posts
    196
    With a mess like that Ms K would be so embarassed. LOL HA HA!!

  6. #6
    Join Date
    Oct 2008
    Location
    Fresno, Ca
    Posts
    4,032
    Oh merciful Heaven...someone clean that shop!!! What did you think of the BB?...the shank diameter always worried me, but the Packard seem stout.
    Your Respiratory Therapist wears combat boots

  7. #7
    John,

    That is pretty much the same grind as I put on my forged pattern gouge. Same thumbnail, and same angle, although I sweep mine when grinding, and it looks like this one may be just rolled.

    When coming around the end of a piece, there is a tendency to only raise the handle, and not sweep the handle. This will cause the cut to move up on the nose and the bevel to lose contact. If the handle is swept and raised (move the tool rest first), the gouge cuts sweet on larger diameter items. I find a 1/2" is easier to control on 3" or so and smaller when making that cut.

    You are going to like that gouge, and I'm betting get a 3/4" or 1".

  8. #8
    Didn't really see any mess in the photo. John, I ground 1" BB SRG sort of like the Continental gouge and I think it works similiar on outside of hollow forms in spindle mode. But your Hamlet (Packard) would be viewed by others as safer.

  9. Somebody call the police..........[shop police, that is..... ]
    Remember, in a moments time, everything can change!

    Vision - not just seeing what is, but seeing what can be!




  10. #10
    Join Date
    Jan 2008
    Location
    Chicago Heights, Il.
    Posts
    2,136
    I think you have attain a new level in "lathe art". I love the flowing curves and well distributed subject matter.
    Member Illiana Woodturners

  11. #11
    Join Date
    Oct 2009
    Location
    McMinnville, Tennessee
    Posts
    1,040
    Oh I'm shock!!!
    Sid Matheny
    McMinnville, TN

  12. #12
    Mess??? LMAO! You won't even make the first cut with a "mess" like that. My sock drawer has more sawdust in it. I do like the new tools though. I got one of those big roughing gouges a while back but I'm askered to use it!
    David DeCristoforo

  13. #13
    Join Date
    Feb 2008
    Location
    lufkin tx
    Posts
    2,054
    That's so clean it makes me nervous. glad you tried the cont. gouge. been wanting one for years. keep us informed on that momma. Avoid brooms, the IRS and copperheads. --------------Old Forester

  14. #14
    Join Date
    Jan 2005
    Location
    Goodland, Kansas
    Posts
    22,605
    Looking forward to hearing a review on it John.
    Bernie

    Never put off until tomorrow what you can do the day after tomorrow.

    To succeed in life, you need three things: a wishbone, a backbone and a funnybone.



  15. #15
    Join Date
    Jan 2009
    Location
    Alaska "The Fish Or Die" State
    Posts
    241
    Not only is the shop in horrible disarray did anyone set eyes on the dust collection setup/gadget behind the lathe? It looks like it was put together with a hose clamp, bailing wire and a few foul words. John Keeton you better get your act together. I hear this forum has some pretty high standards, and you’re dancing on a fine line of some kind of disciplinary actions, or something........lol
    "There is nothing more dangerous than a resourcful idiot".....Dilbert

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •