Search:

Tag: plastic

Search: Search took 0.00 seconds.

  1. Anyone plane UHMW polyethylene? Gotchas to watch for before I start?

    Started by Justin Meyer, 09-18-2019 10:31 AM
    2 Pages •
    1 2
    machining, planing, plastic, polyethylene, uhmw 2 Attachment(s)
    • Replies: 23
    • Views: 3,468
    Last Post: 10-29-2019 2:27 PM
    by Mark Bolton  Go to last post

    Forum:
    General Woodworking and Power Tools

  2. Laser cutting plastic less than .1" thick

    Started by Todd Mueller, 05-02-2016 11:06 PM
    air, clamp, hold, plastic, thin
    • Replies: 10
    • Views: 2,691
    Last Post: 05-03-2016 4:38 PM
    by Lee DeRaud  Go to last post

    Forum:
    Laser Engraving General Topics

  3. Is this resin? How to cost effectively recreate?

    Started by Patrick Collins, 06-23-2015 8:06 PM
    art, epoxy, plastic, resin 1 Attachment(s)
    • Replies: 4
    • Views: 1,632
    Last Post: 06-24-2015 8:10 AM
    by Pat Barry  Go to last post

    Forum:
    General Woodworking and Power Tools

  4. Looking for sheet acrylic supplier - Oregon

    Started by Al Stewart, 11-03-2009 11:44 PM
    acrylic, plastic, supplier
    • Replies: 14
    • Views: 7,637
    Last Post: 09-30-2013 2:13 PM
    by Bob Sandle  Go to last post

    Forum:
    Laser Engraving General Topics

  5. Best glue to adhere plastic to MDF or plywood?

    Started by Joel Griffies, 10-29-2011 9:22 PM
    glue, lego, lego table, plastic
    • Replies: 14
    • Views: 47,427
    Last Post: 03-11-2013 8:41 PM
    by Brad Cambell  Go to last post

    Forum:
    General Woodworking and Power Tools

  6. Is "urea plastic" relatively safe to laser etch?

    Started by Chris Schenck, 05-13-2012 12:49 AM
    laser, plastic, safe, urea
    • Replies: 7
    • Views: 4,053
    Last Post: 05-18-2012 7:57 PM
    by Michael Hunter  Go to last post

    Forum:
    Laser Engraving General Topics

  7. Laser plastics for car badges

    Started by James Terry, 04-01-2012 1:08 PM
    laser, plastic 1 Attachment(s)
    • Replies: 6
    • Views: 2,554
    Last Post: 04-02-2012 11:18 AM
    by Darryl Hazen  Go to last post

    Forum:
    Laser Engraving General Topics

  8. Acrylic or PVC?

    Started by Freida Kirkland, 04-29-2009 8:53 PM
    acrylic, cutting, plastic, recycling, television
    • Replies: 6
    • Views: 4,042
    Last Post: 05-01-2009 9:24 PM
    by Richard Rumancik  Go to last post

    Forum:
    Laser Engraving General Topics

  9. Laser Etching ABS Plastic with a Rabbit

    Started by Ron Baywalds, 05-20-2008 8:35 PM
    abs, etching, plastic, rabbit
    • Replies: 1
    • Views: 1,114
    Last Post: 05-20-2008 8:42 PM
    by Joe Pelonio  Go to last post

    Forum:
    Laser Engraving General Topics

Results 1 to 9 of 9