Curt Harms
Contributor

If you're able to get a good clean rabbet you may not even notice any gap. Well, YOU will because you know it's there but others likely won't.

Google probably has the most expertise at "connecting the dots" in a person's life. There are competent search engines that still respect one's...

I'm not familiar with the Infinity set but the Freud set looks like an upscaled version of their cabinet rail & stile kit. The thing that is unique...

I think that's a problem with SSDs in general. Spinny HDs usually give some indication they're about to fail, SSDs don't, they just quit.

I don't know that it'd be practical $$ wise but you could install a transfer switch like generators require. Either the dryer or tool outlets would...

I don't recall where I saw the idea or I'd link to it. The cabinet is similar to the "Norm style" router table, rectangular cabinet with a ...

Some routers will let you specify a starting and ending DHCP range.

If your bandsaw will work with a real carbide blade that may work. For me it wouldn't unless I upgraded my bandsaw (Rikon 10-325) to something like a...

David, I think I found a manual (in German) for your router https://www.manualslib.com/manual/1162029/Parkside-Pof-1200-B2.html If that is the...

That's what I did, crimp splices and bullet connectors. I used wire sold as bell wire and put one male and one female connector on each wire to...

Bosch does have service centers, I bought a couple Bosch refurbs at one. But yeah, the economics of repair vs. replace.

I have a PAR30 type lamp that will flicker sometimes, its mate doesn't.They were purchased a few years ago and fairly early in the affordable LED era.

I was thinking of a bearing guided slot cutter like this: ...

Crucial is part of Micron, a HUGE flash memory (and other solid state stuff) producer. You did well.

Good job Glenn on the grandson. SWMBO was less diplomatic with her adult daughter. The question to ask with most tech stuff is who is managing who?...

That was my thought as well. Combos and separates fit best in different scenarios.

I think Mike has it. A 14" saw will resaw but not fast. A motor upgrade may help but IMO a 14" cast iron saw will not support a 'real' resaw blade -...

That's what I've done with our Printer/MFDs. I had problems with devices not being found when using DHCP, problems went away with static IP...

I did what Scott did, built a stout 2" X 4" rolling cabinet with 1/2" ply panels. There is a lot of storage in that cabinet. I haven't found myself...

Those are nice Ole. I've seen some hickory that was way too 'rustic' for my taste. Heart & sapwood mixed nilly-willy, yuck.

Lenox TriMaster is available in 1/2" width and .025" thickness. I wonder how that would work on common 14" saws. Ain't cheap though at $179.83 here:...

That's pretty much what I have now but had a lot of chips in the cartridge filter. I cleaned the cartridge filter well, I can use a garden hose on it...

I think the biggest issue with frequent starts on induction motors is heat rather than electricity use. There's quite a bit of heat created in a...

Barrier coat of dewaxed shellac between the poly and paint? That's an accepted technique for indoor furniture, don't know how it would work outdoors.

As Jim says, as little down pressure when face jointing as you can get by with. I use a 'shoe' with a heel to be able to push horizontally without...

Jersey gas is still 25-30 cents/gal. cheaper even with the .25/gal tax increase. And many small/independent Jersey stations charge 6 cents/gal. for...

I would go with Jim's advice and talk to American Filter Fabric. You can tell them what you have and they will give you a recommendation. It will...

There's Miracast but I know absolutely nothing about it beyond the name. We have Tivo that has Amazon Prime & Youtube and others built in. Here's...

There are a lot of homeowners that would find Harbor Freight hand tools perfectly adequate to assemble their latest KD cabinet or 'furniture'...

My understanding - and I'm no expert, just know what I read in the paper - that being an LLC or sub S corp. provides limited protection. If there is...