Register
Help
Remember Me?
What's New?
Forum
New Posts
FAQ
Calendar
Community
Groups
Albums
Member List
Forum Actions
Mark Forums Read
Quick Links
Today's Posts
View Site Leaders
Articles
Blogs
Donate
Sponsors
Friends of the Creek
Advanced Search
Member List
Stew Hagerty
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Stew Hagerty
Member
Find latest posts
Find latest started threads
View Articles
View Blog Entries
Mini Statistics
Join Date
04-15-2010
Last Activity
05-29-2019
4:45 PM
Avatar
More
9
Friends
tom coleman
Bob Smalser
Glenn Kotnik
Prashun Patel
Ricc Havens
Al Launier
Join Groups
1
Groups
Wheelchair Woodworkers
Join Groups
0
Permission Groups
Stew Hagerty is not a member of any public groups
Recent Visitors
The last 10 visitor(s) to this page were:
Aiden Pettengill
,
Al Launier
,
Asher Carmichael
,
Dirk Ellis
,
Erik Jensen
,
gary wallen
,
Kevin Stafford
,
Lenny Howard
,
Nike Nihiser
,
Robert E. Steele
This page has had
20,111
visits
Tab Content
Stew Hagerty's Activity
About Me
Friends
Tab Content
All
Stew Hagerty
Friends
Photos
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
05-11-2024,
9:15 AM
Ricc Havens
replied to a thread
liqudating entire wood shop
in
SawMill Creek Classifieds
Thanks David, but I will pass. I'm looking for Vicmarc chucks.
see more
20 replies | 1810 view(s)
05-10-2024,
8:40 AM
Ricc Havens
replied to a thread
liqudating entire wood shop
in
SawMill Creek Classifieds
I sent you a PM asking if you had any chucks. If so, what did you have and what the price? And your only response was - "everything is priced at...
see more
20 replies | 1810 view(s)
05-09-2024,
9:11 AM
Prashun Patel
replied to a thread
Stainless steel figure 8 hardware
in
General Woodworking and Power Tools
Google "Table top buttons". I've used this method a few times. You can use stainless steel screws to attach them. You need an easy way to route...
see more
15 replies | 1002 view(s)
05-08-2024,
8:41 PM
Prashun Patel
replied to a thread
Should I replane three week old edges before glue up?
in
General Woodworking and Power Tools
To test a panel joint, I slide post it notes between the joint at various points and then dry clamp them with "moderate force". If I can't pull any...
see more
8 replies | 936 view(s)
05-07-2024,
10:21 AM
Prashun Patel
replied to a thread
Outdoor White Oak
in
General Woodworking and Power Tools
It will turn silver. Washing and oiling will delay the decay and possibly splitting. On outdoor furniture you can also epoxy any end grain -...
see more
11 replies | 798 view(s)
05-06-2024,
3:21 PM
Prashun Patel
replied to a thread
Dewalt DW735 Planer for short hardwood boards?
in
General Woodworking and Power Tools
I don't think the width of the planer has much to do with it's ability to handle short stock. Anything under 12" is a challenge to run through any...
see more
16 replies | 1176 view(s)
05-06-2024,
2:12 PM
Prashun Patel
replied to a thread
Charcuterie Board Handle
in
General Woodworking and Power Tools
Most ergonomic for me is recessed handles on the underside and felt or rubber feet to give a shadow line, help it sit flat better, and reduce slip...
see more
15 replies | 1119 view(s)
05-06-2024,
8:16 AM
Prashun Patel
replied to a thread
Outdoor White Oak
in
General Woodworking and Power Tools
Here's a white oak bench I made 10 years ago. I finished it initially with something - I can't remember. That lasted 2 seasons, and started flaking...
see more
11 replies | 798 view(s)
05-03-2024,
7:27 AM
Prashun Patel
replied to a thread
Creating an aged maple finish
in
Project Finishing
I'm pretty comfortable with dyeing and toning. I've done a fair bit of it, including matching and layering for color depth. I agree, the...
see more
21 replies | 3205 view(s)
05-02-2024,
5:21 PM
Prashun Patel
replied to a thread
Creating an aged maple finish
in
Project Finishing
Thanks for the follow up. I learned a lot on this thread. Mostly that coloring is not something I want to do ;) Thanks for the Minwax OMP review. ...
see more
21 replies | 3205 view(s)
More Activity
No More Results
No Recent Activity
About Stew Hagerty
Basic Information
Date of Birth
July 30, 1959 (64)
About Stew Hagerty
Location:
Ft. Wayne, IN
Occupation:
Disabled
Signature
"I've cut the dang thing three times and it's STILL too darn short"
Name withheld to protect the guilty
Stew Hagerty
Statistics
Total Posts
Total Posts
1,453
Posts Per Day
0.28
General Information
Last Activity
05-29-2019
4:45 PM
Join Date
04-15-2010
9
Friends
Al Launier
Member
Bob Smalser
Member
Glenn Kotnik
Contributor
James Green 2
Member
Michael Sapper
Member
Mike Gottlieb
Contributor
Prashun Patel
Moderator
Ricc Havens
Contributor
tom coleman
Member
Showing Friends 1 to 9 of 9