Register
Help
Remember Me?
What's New?
Forum
New Posts
FAQ
Calendar
Community
Groups
Albums
Member List
Forum Actions
Mark Forums Read
Quick Links
Today's Posts
View Site Leaders
Articles
Blogs
Donate
Sponsors
Friends of the Creek
Advanced Search
Member List
William Hodge
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
William Hodge
Contributor
Find latest posts
Find latest started threads
View Articles
View Blog Entries
Mini Statistics
Join Date
11-28-2012
Last Activity
Today
12:54 PM
Recent Visitors
The last 10 visitor(s) to this page were:
Carroll Courtney
,
Chuck Saunders
,
Darrell Bade
,
Greg Parrish
,
Lloyd McKinlay
,
lou sansone
,
Mel Fulks
,
Patty Hann
,
Stephen Prunier
,
STUART Robertson
This page has had
4,962
visits
Tab Content
William Hodge's Activity
About Me
Tab Content
All
William Hodge
Friends
Photos
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
Today,
12:54 PM
William Hodge
replied to a thread
Safety switch test
in
General Woodworking and Power Tools
Plugging in a machine or power tool with a manual switch in the on position will wake you up. I worked in a shop where there were a lot of people...
see more
13 replies | 502 view(s)
05-17-2024,
12:49 PM
William Hodge
replied to a thread
Odd molding profile
in
General Woodworking and Power Tools
Here is a drawing of a router bit that makes pencil beads in one set up, two passes. It matches an old molding. The fillets are off set and...
see more
13 replies | 778 view(s)
05-09-2024,
8:08 PM
William Hodge
replied to a thread
Beaded faceframe tooling question (grinding shaper cutter)
in
General Woodworking and Power Tools
I like corrugated back cutters for fine details like a bead fillet. CT Saw and Tool can make them pointed, like the old hand planed beads. Carbide,...
see more
12 replies | 1286 view(s)
05-08-2024,
6:30 PM
William Hodge
replied to a thread
Total Boat Epoxy?
in
General Woodworking and Power Tools
Carrol, Can you put up a photo of the two sashes to be glued side by side? This is new to me. If it's stile to stile with a spline in between,...
see more
6 replies | 658 view(s)
05-05-2024,
3:15 PM
William Hodge
replied to a thread
Dewalt DW735 Planer for short hardwood boards?
in
General Woodworking and Power Tools
I have a 20' Powermatic planer and a Dewalt 735. I use the Dewalt as a finish planer, and the Powermatic as a roughing planer. The high speed steel...
see more
16 replies | 1494 view(s)
05-03-2024,
9:52 PM
William Hodge
replied to a thread
New to me mortiser
in
General Woodworking and Power Tools
The chisel bevel angles vary quite a bit. I buy assorted cone shape stones that go into a drill. I change the angle on them by spinning them in a...
see more
15 replies | 1541 view(s)
05-02-2024,
12:59 PM
William Hodge
replied to a thread
Shaker Window Sash Profile
in
General Woodworking and Power Tools
Tom, It's great to see someone matching existing sash, through tenons and all. No Dominos and epoxy.
see more
36 replies | 2582 view(s)
04-29-2024,
5:55 AM
William Hodge
replied to a thread
Shop Vac for Table Saw Dust Collection
in
WorkShops
I have a little Dust Deputy cyclone on a 55 gallon drum, all outdoors. The 55 gallon drum really seals tight.The exhaust has some fine dust in it, I...
see more
18 replies | 6945 view(s)
04-27-2024,
1:54 PM
William Hodge
replied to a thread
Shaker Window Sash Profile
in
General Woodworking and Power Tools
Here's a profile from a shaker building. These are custom cutters, but the profile is a copy of an 1840's Shaker sash.
see more
36 replies | 2582 view(s)
04-26-2024,
12:38 PM
William Hodge
replied to a thread
Shop Vac for Table Saw Dust Collection
in
WorkShops
I use an Ultra Clean central vac. It's great for the floor, sanders, rip saw, etc. Air Flow: Air flow of 135.2 (CFM) cubic feet per minute...
see more
18 replies | 6945 view(s)
04-25-2024,
12:41 PM
William Hodge
replied to a thread
Glaziers Points Sizes
in
General Woodworking and Power Tools
The points for narrow rabbets are #1 diamond points. ...
see more
21 replies | 1479 view(s)
04-25-2024,
10:05 AM
William Hodge
replied to a thread
How to bend wood like this - Outdoor furniture project
in
General Woodworking and Power Tools
I agree, 2" truck straps work great. Pad the laminations with some bending plywood. The note above warning about sanding wood to be machined is...
see more
167 replies | 18538 view(s)
04-24-2024,
6:17 AM
William Hodge
replied to a thread
Making screen panels for a lake view
in
General Woodworking and Power Tools
Try using The Google. "Sossry" is right there. I never knew, hadn't come across it, added a new facet to this jewel of a day. ...
see more
25 replies | 2395 view(s)
04-23-2024,
12:58 PM
William Hodge
replied to a thread
Making screen panels for a lake view
in
General Woodworking and Power Tools
The choice of wood can depend on the amount of water hitting the screens. Some screen houses have pretty good over hangs, and the screens don't go...
see more
25 replies | 2395 view(s)
More Activity
No More Results
No Recent Activity
About William Hodge
Basic Information
About William Hodge
Location:
North Dana, Masachusetts
Statistics
Total Posts
Total Posts
503
Posts Per Day
0.12
General Information
Last Activity
Today
12:54 PM
Join Date
11-28-2012