This is a great attitude to take and a lot less stressful.
Being an owner of several Jet machines and a Powermatic 14" bandsaw I have been very happy with the company and I will continue to...
Type: Posts; User: Samuel Brooks; Keyword(s):
This is a great attitude to take and a lot less stressful.
Being an owner of several Jet machines and a Powermatic 14" bandsaw I have been very happy with the company and I will continue to...
I picked up a Jacob's Replacement Chuck for my Ryobi at Home Depot for around $25.00 and it has not slipped once. I have had it for almost a year now. It's like a new drill. I never had issues with...
Very inspiring - Great Job.
Sam
Thanks for sharing.
Sam
I am working on a project that I want to fill in so routed designed with gilding. This will be my first project doing this. My question is the following.
The project is in Red Oak, I am going...
I would swap the location of the Jointer / Plainer with the Drill Press, Bandsaw and Router Table. In most cases when you are working with raw lumber it will be larger then it is by the time you...
What makes you ask if you want to use a grain filler? What is your desired results that you are shooting for?
Please note - I have never tried using grain fillers so apply your own situation to...
The column is out of solid oak since it's only 2-1/4 inches. I used 6/4 and did one lamination.
Thanks,
Sam
I like the idea of putting in a transition, I might put in a bead detail at the junction point then maybe put a few others trought the column to hide it.
I have a special drill press table that...
I need to produce (4) turned 2-1/2" columns with each being 76" tall.
38" is the largest turning that I can do with my lathe, so I am thinking of turning the two separate columns and joining. ...
You can run lots of stuff from DSL connection if it's available in your area also do not overlook Cable Service. I have apartment communities that run 3-5 PC's that all share a single DSL connection...
The 23 Gauge Air Pin is Model 97526
On the outside of the box it shows 97526/95882. This does not have have the bump safety.
Thanks,
Sam
I just wanted to get the project done. Next time I pull it out, I will put some tape on the rear connector. I did use tape on the adapter.
Thanks for the Comments.
Sam
I had a project that required attaching molding that was 1/4 x 1/4 cove molding on the top and bottom edges of all for sides plus another build up molding.
The Project:
100624
The Nailer:...
Tightbond III. The veneer is flaming birch and is about 1/16th thick over popular. The top is over plywood.
Sam
I have been working on this project for several months and have finally hit the home stretch. I learned how to veneer and have had allot of fun. New Drum Sander and Pin Nailer - Bonus :rolleyes:.
...
This was it. I have been "gentle" with the pens so I just turn until I feel resistance. I just needed to turn past the Resistances about 1/8 of a turn and it locks. Imagine that :-). This is a...
I find that I press down pretty hard when I write and this causes the twist pens to twist back into themselves. Has anyone else come across this and do you have any "quick" fixes to make the pens...
I second that note.
Sam
My brother-in-law said something about guide wires. I am not familiar with the anatomy of pole installation, so I will ask him for specifics next time I speak with him. Thanks for the comments.
...
Here is the end grain. I tried cutting with a handsaw but it still "smears" the end grain just like I took sandpaper to it.
98831
Here is another look at the wood partially plained.
98832
...
What determines the size of the spacer used between the boards?
Thanks,
Sam
My wife picked me up one of these for a present. I kind of though it was a joke when I first saw it, but I find that I adapted to it really fast and it has become my goto tool instead of the hand...
How would you go about testing wood for contaminates? Before I read this, I was thinking about doing a glueup and making a kitchen table out of this.
Thanks
Sam
It was used to hold up telephone poles. It has been outside for 20+ years and this is what I got after I removed the weathered shell.
98759
It is very hard and does not dent if you try to...