The photo from post 4 is exactly like my machine. The 3 center iron brackets hold the grub screws. On mine the screws were not touching the platen initially and the platen was resting against the...
Type: Posts; User: Joel Wesseling; Keyword(s):
The photo from post 4 is exactly like my machine. The 3 center iron brackets hold the grub screws. On mine the screws were not touching the platen initially and the platen was resting against the...
My sander arrived out of the crate - not set up flat. It had an inward deflection in the middle of the sanding plate.
It has adjustments. Locking grub screws that push on the back side of the...
Thanks!.. I'll stay with one inch!
Max Blade Width for FB610
So, I've owned FB610 for 3+ years now. I wore out my 1" resaw blade!
The max width shown on the saw tension scale is 1-3/8" but specs on felder site state blade width...
Thanks, Erik.
I was hoping Hammer will offer a value packed wide sander - I'm looking at drum units, possibly Woodmaster.
The bucket on my Kubota will do the lifting.. I could use HS-950 right...
Thanks! Secured my order for HS950 last week.
I'm really curious about new models from hammer. Any news?
They are available. $3500ca. 12-16 week lead time.. The price seems high considering its $2000usd. Can I get a better machine for $3.5k
Any changes - will the hammer sander come to Canada?
Is there other Euro or NA machines around the price of the Hammer. THX.
Funny! Nice work too.
It's a copyright picture. Can I re-post it here? Crop a small section? or No?
Can anyone be certain from the pic?
FWIW, the canadian Hammer site shows a list price of $2573can
Did you purchase a mill? I've been looking online at the entry level mills. Really curious if the LT10 is good choice - the price is as high as I want to go.
I have the EGO 56V cordless string trimmer and chainsaw. They are both amazing, high torque and about 30 minutes of weed trimming before a charge is needed.. I did a lot of research before I took the...
Have 2 Dewalt 20V drills. Batteries are excellent. I put these drill to hard use, the transmission went in one of them last week, I hope to replace the tranny.
Meantime I purchased the newer...
A fine grind with Isopropyl makes things worse, unless the container is shaken continuously without stopping until all flakes are dissolved.
The downside - It takes a long time to dissolve the flakes, it takes days and requires a lot of shaking to prevent the shellac from congealing to the sides/bottom of the container.
The upside - it...
Ripping with my FB610 is a pleasure! Very easy to resaw 16" as well.
Virutex PEB250 Vs Felder 200 ECO Plus - Any experience and opinions
Earlier this year I found a bench made of hemlock. It was outside for 8 years, black and covered with lichen. The power washer cleaned in up really nice. I've sanded it and its now ready for oil.
Many One box units house Class D amplifiers(digital amp is incorrect terminology). Class D amps contain analogue switching devices and turn the analogue signal into Pulse Width Modulation.
The...
Im not using pre-glued edgebanding! The Festool machine is a contender - Thanks!
Thanks. I will try Fastcap Speed Tape on a small project to test it out. edit-now I see hotmelt tape online - have to research this more. The Felder machine is about CA$2800, I can purchase one when...
Need inexpensive hot melt edgebander or is there a way to apply egebanding without a machine.
I have a few cabinet jobs. I'll be using sheets of Uniboard melamine with patern matching edgebanding...
The cobalt knives cost me CA$200(incl tax) for two sets for A3-31. Im still using the first of 4 sides after 6 months of low to medium usage, and the initial sharpeness appears to have not changed,...