Search:

So my co-worker and I have been going through the tutorials suggested as well as some that JDS put out. The owner is convinced that we should throw ourselves completely into Corel Draw over...

In playing around with Corel, we were concerned about using the matrix. Come busy season, we are pumping out thousands of trophies with pretty much the same label but maybe a name changed on each...

We finally bit the bullet and are changing over from Gravostyle to CorelDraw. I am looking for some advice on the best tutorials. They have used Gravostyle for at least 20 years here so this is a...

We wanted to be precise. I was hoping someone had the same machine and maybe replaced a lens recently.

GravoGraph never got back to us on this and several other issues. We tried several times. We are also dealing with a rotary engraver start button not working.

I have been tasked with finding replacement lens for our Gravograph LS800. I keep hitting dead ends. There is information that was lost a long time ago that I need to find the right one. Does...

I tried recleaning & tightening everything. Below is a picture of what happens when I tried to engrave on flexibrass. The double lines on the right are from the the carriage moving into place. ...

We had a client come in with a coffee table book of photographs that he wanted us to make placemats for his cafe with the cafe logo on the photo. I looked into the rights on the photos. He could...

I have tightened everything, dusted everywhere I can get at. I watched from start to finish. Instead of the beam engaging at the start of the engraving, the beam engages as soon as I press start...

Slightly different. The front is not open like that one. I do have air here that I used while cleaning but I think I am going to have to take apart a few new places to get some of the dust out. ...

It is on the New Hermes which I found out is really from Universal.

I did think it was a dust issue somewhere.

Suddenly, out workhorse has been engraving extra lines on out material. At first is started with small vertical dashes so we cleaned the laser. Now it is engraving long, horizontal lines.
...

Thank you for all the replies. Hopefully this information will help with our scrap clutter.

We are having a great debate here.

What do you do with your cut off materials that are too small for making plaques, etc but too big to deem scrap for recycling?

We have racks of cut off...

I have to reassure my boss that this is doable because the Gravo rep just told him it wasn't. It is our LS800 that keeps glitching on us with no end to the repairs in sight. He wants to replace...

It can do both normal printing and they have the laser icon. There was a recently software issue that customer service screwed up our drivers and until they could figure out what they did we had to...

Question or questions for you all:

We are in the market for a new laser. My boss is looking at getting a 75w Epilog.

Can this machine run using GravoStyle 5?

We have had nothing but...

Great.....thank you.....we already have to print that way on the older laser so that would not be too much hassle. It is a weight off my shoulders.

The owners are looking into getting a new laser. The store has been using Gravostyle and its ancestors since they opened. All of the lasers are Gravograph/New Hermes.

Can the Gravostyle...

I was reading about the lower the speed the more burn just now. The problem is the setting used here in the store were established by the previous owner. I came on board after the owner change and...

I have played around a bit but it is our busy time so I don't have enough time to play with speed and power to find the right fit for the 30W at this time. So, as of now, it is a fail but when...

We achieved success with our AcrylaThin order with a very simple solution that worked really well on the 25W however I could not get the same results on the 30W.

Running an AcrylaThin plate on a...

We have a client who really wants the granite one but it seems to be more work than it is worth. As we are part of a franchise, we cannot change the prices to reflect the time put into the item. ...

Thank you for the info sheet. It looks hopeless but we are trying.

Hi, I am new to this board and found it because of my search for information on engraving AcrylaThins.

My boss really wants to be able to offer this on a regular basis but currently it takes us...