Search:

==========================================================

You noticed the impeller and HP sizes. Only recently have buyers wised up to the fact that the impeller diameter controls CFM not the...

============================================================
I don't think so. The only companies using aluminum impellers are Oneida and PSI on their cyclones . The rest are steel including DC...

===================================================================================================================================
I've taken apart many Dc's and vacs and they all use radial...

=====================================================================================================================================

AMCA arbitary? Shirley you jest. That''s like saying the SAE...

==============================================================

Sigh, it was a nice clean thread until this post. A shame. But I will answer the questions and comments.

Yes I do love to talk...

========================================================

I think my sentence was perfectly clear but will restate. I use two Clear Vue type blowers in series to power my cyclone. I do not use a...

A very good thread with a maximum of insults and name calling. Thank you. There is nothing wrong with being critical of a new or strange idea. It's a bit of a challenge to put it in a way that...

===============================================================================================================
I think most here realized what a ammeter is for. As I tried to explain the meter is...

================================================================

As I tried to explain it depends on how much time the DC is on. Put the humidifier out side and try to reduce the humidiy in Iowa...

Air does not work like one thinks it should. It's very confusing. To increase CFM in a vac system run the blowers in parallel. To increase CFM in a DC run the blowers in series. You need a fan curve...

The motor will run cooler not hotter because it is doing less work, ie pumping less air. Only liquids cavitate. Airplane props get wear from dust particles but flying though rain will cause...

Good move. One needs as much light in the shop as possible. My shop is very old and needs painting also , so I'm watching this thread. It's an awful job so I've put it off forever. The difference in...

Some where in the past I posted a source for the Jet 1100 blower and others fan curve direct from Jet. You probably can find it with a search. The 1100 impeller is way to small for a cyclone unless...

===============================================================
I don't make up stuff and you have never been able to prove me wrong. I do note that I also have rarely seen any posts by you...

Surprised you didn't get more opinions. And opinions is what the answer to this question is made up with. So I'll give you mine. I assume you are using a bagger rather then a cyclone but I'll give my...

I have some problems and have been trying to figure what to do. My shop is in a walk out basement and the house was built about 20 years ago. It's on unstable soil and has very bad cracks and...

Your making up circuit stuff again. Stop and think the details out before comments. The 220V solenoid and the cyclone and the Toro are controlled by a 24V system though relays of course. Gee, do I...

I can't figure out why you are so afraid of power cords? Most saws and tools come with them. You do not need hard wiring unless your local code requires it which is rare. Nema box for an solenoid?...

My cyclone and blowers are outside next to the shop. No, not a 100 yds. Just a few feet in a small shed attached to the house. The cyclones exhaust has a damper on it but its not air tight. So cold...

Funny you should ask. In a post in the blast gate thread I mentioned the Sears Auto Switch . I have two of them mounted to the shop vacs. Sounds like a good idea but in practice I don't use them...

I still can't see the need for a current sensor when a direct wire gets the job done. PF with the cheap power we get and the number of hours my tool run I don't worry. While the PF is much less then...

I just typed in the CR magnetics model 9350 that you showed and $30 came out. What do to I know?\Since your shop is old how much would the parts cost into days money? I use plug strips on my...

========================================================================================
I can't figure out why one would want to use an expensive $30 sensor when there is absolutly nothing unsafe...

Blast gates get no respect. A simple device that gets ignored. You just can't buy decent gates. The elCheapo plastic ones fit inside the duct work. That restriction reduces the duct diameter about...

Chip, the FWW 143 issue dates back 11 years. I used to save them but trashed whole lot when doing my yearly clean up a few years ago. As I remember it had something on sensors but no method of...