Search:

are any of the other options okay?

I have a drawer front that is thinAnd flexible. Only 1/4 of an inch with a 1/2 inch backing. My handle has 2 Machine screws which is fine, but the door is wide and I think screwing from the inside...

the only issue I have with shims is, when the angle have to match the offset?



what is the proper way to cut a tapered board. I've never seen a taper made where the thickness of the board...

Hello,
I just installed a cabinet of full extension drawer slides. They slide smoothly so my drawer width is good. No binding. I took a lot of care to keep things level, True and within tolerance....

12 mm frame, 5 mm front ( plan) not executed yet. Wait a second. Why does the drawer need two handles? I only bought for one.I fitted one test drawer and it is ultrasmooth. I disabled the soft close...

Does the hot glue last for years with temperature changes? Despite the fact that this is all made out of Baltic birch plywood, is there any issue with movement? I shouldn't think so since many...

Hello,
I just built some drawers and I assembled the bottoms without glue. They are floating this was for ease of installation. However I've run into a potential issue down the line. Because the...

how do i pull the back in or out? each drawer is about 20"x40". some of the drawer bottoms are 1/4"BB and others 3/8" BB

it wasn't off shore chinese. I remember buying it at Home Depot ages ...

Hello,
I bought some 12mm Baltic birch plywood to build some shop drawers.I miscalculated the amount of material needed by only one or two drawers. looking around I have two options I have...

if the hose size changes, the CFM should remain marginally the same, not air speed. airspeed is what should change.

good idea on hose change sizes depending on application.

the case i would...

i am a bit blow away by this. never would habe thought about it.



now this i dont quite understand. why do i have to reduce the speed? (what is the Consequence of higher suction)




if...

is that a 3.5" or 36mm.I think there was a typo there. This is good. I just didn't want to purchase something expensive without knowing for sure.



I would just love to see if anybody has...

A point of clarification. dust extractors typically come with 1 1/2" hose. I'm looking to convert this to a larger 2 1/2" hose, not a smaller one. this is the opposite situation of a dust collector...

what happens to CFM when dust extractor is hooked up to 2 1/2" port or 2 1/2" hose? Trying to determine if a dust extractor is a good replacement for my dead shopvac. I want to use it for a bandsaw...

I had not considered the swelling. How loose should it be?



and you had no negative consequences for not clamping?
I will definitely be buying tight bond extend.

in Matias's video, he...

newb question.
Just as it says in the title. I recently saw Mattias Wandel's channel last week make a drawer with the box joint and no clamps. I have never made a box joint project before. the...

Hello,
I'm trying to maximize the amount of vertical space Under a shop table I will be Building in the shop. every inch counts. there are a few reasons why this needs to be done. This tabletop...

I understand the sentiment. but this is the reason. when you have experience, you know what is considered good enough. when you have less experience, there is more of a tendency to over build or...

baltic birch ply edge. hard to glue to that. Unless I hogged out a larger area and glue to bottom.



Great resource. although the chart does cite bolts in holes. I can understand the tolerance...

I cut my 3/4" router slot on My band saw table/ I went for 3 passes ( by mistake) to cut the total depth. I accidentally cut it to wide. by 0.020".

I figure the fix is to put UHMW tape in the...

That's for aluminum. with the same apply for plastic?

I built an "over table" for my bandsaw. it is an 18mm thick table. I bought uhmw runners(3/4") wide and 3/8" tall at lee valley.
Should the uhmw touch the sides of the table only or touch the...

I have 18 mm plywood that I intend to use as a bandsaw table on top of my existing aluminum table (12" delta). reason for doing this, is the existing table is is not flat, and dips in in the centre...

I would love to hear the result. hopefully that made the difference.

Do you think you would've had this issue if you were using bags? I know a lot of people don't use them, but I've always been a bag person since the beginning, and would think the clogging would be...