Thanks Dan. That's what I was not sure about. So it does not matter which you hook up to black or white. Just did not want to burn anything down!
Darren
Type: Posts; User: Darren Vass; Keyword(s):
Thanks Dan. That's what I was not sure about. So it does not matter which you hook up to black or white. Just did not want to burn anything down!
Darren
Thanks for the heads up. Below is a pic of the wiring cofig in the manual. It is to 110/115.
Thanks,
Darren
http://i1025.photobucket.com/albums/y313/dian1511/P10101241077x808.jpg
http://i1025.photobucket.com/albums/y313/dian1511/P10101211632x1224.jpg
Hi All,
My bandsaw has been laying dismantled since June 2008. I'm putting it back together again, but am not...
Thanks for the ideas. It does seem that a router is going to be DIFFICULT. I'll look more into bending, perhaps with kerf cuts and also into a large dowel.
Thanks again,
Darren
I'm working on building a subwoofer. I really like the box in the pic below, especially in nice veneer. It is a 20 inch cube with wall thickness of 1.5 inches, MDF. Does anyone have an idea of how to...
Thanks for all the replies. I went to Woodcraft and they were kind enough to open cans and try product on test pieces. I found Empire Red ready made water soluble die that is perfect. Applied it last...
I've been working on a pair of loudspeakers. Tiger Maple veneer over Baltic Birch ply.
Here is a pic of the back. The sides are the same:
145304
I wish to do the baffle or front of the...
Thanks Rod.
Myk,
So I don't need to get a DPST switch. Just get a regualr wall switch from Home Depot and hook it up?
http://grizzly.com/products/110-220V-On-Off-Switch/H8238
Wondering whether this Grizzly magnetic switch would be safer than the DPST rocker switches?
There are two black and two white wires...
Guys,
Thanks for your replies. I've changed out warn out switches in the house, but never anything like this. Here is what I found on ebay for square D 2510:
...
I've been routing holes for about 3 hours. I've been turning the HF dust collector off and on throughout, not very often. The switch seemed stuck on ON the last time I tried to shut it off, so I...
Matt,
Great Job. Looks very professional. I am curious to know how the dust collection works. I placed my duct on the bottom of the box and you placed your on the back. When I used mine, I found...
Found my answer in the finishing section. Poly can go on shellac if it is dewaxed.
Chris,
Thanks man. I like both ideas. They both seem more stable and doable. Thanks again.
Darren
George,
I'm using a Milwaukee 5616 2.25 hp in the fixed base. The phenolic plate looks like the generic one I see many places with the concentric circles on the back side for lining up the holes...
Last night, I tried to flush trim a 3/4 inch edge on an 8 x 12.5 x 3/4 inch piece of board (baltic birch). I had glued up 3/4 inch edge banding on either short end of the board. The edge banding was...
Hi Terry,
How and where would one dowel into with a mitered corner box?
Thanks,
Darren
I am making a small box for a loudspeaker. It measures about 8 W x 8 D x 13 H inches. The corners are mitered along the 8 inch sides. During the dry fit, I tried the masking tape on the mitered edges...
I decided to check the usual that has been advised here. The drill bit is straight and true. The table is dead flat.
The silver square is not. I placed it within another square and it was short...
I just put together this drill press from Harbor Freight. I was setting it up and I am finding it difficult to square the table. I will label pics to follow. I hope someone can give me some...
This seems to be a good deal, at least no worse than the other similar models, sold by different vendors.
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=43378
Any thoughts?...
Again, thanks for all the replies. Yes, I'm trying to counterbore, that is to get a larger flat bottomed hole on which a flat head (the bottom of the head) will sit. The smaller hole is also slightly...
I am drilling holes in my router table base plate for my router. The router baseplate has countersinks that are almost 1/2 inch in diameter but with a flat bottom for a flat head screw. How do I...
Thanks to all the great suggestions. I've never thought of CL, but will keep my out on it for deals. Thanks again.
Darren