Search:

I am looking for a new RO sander I have a Milwaukee right now. Every time i use it ( sometimes only 1 hours use) i have to replace the brake pad so the sanding pad dose not spin at a high rate of...

2 words SHARK GUARD!!!!

the new shop is the former Garage there will be no garage doors ect. it should be treated like any other basement shop in my opinion. or am I totally missing the point on the fire break? I will...

the home is in the country and very..... lax codes there will not be any autos there. Going to build a new garage with no steps to home. how is the best way to hang cabinets to the concrete...

were buying a new home it has a 2 car garage in the basement that will be turned into my new shop.
Any ideas or suggestions on fininishing out the walls? What about the celing above the shop will be...

My shark stays on for every cut that can be made with it on. If I have to take off to make the cut I will try to do it another way if possable.

I have the leevally one and really like it. I would recommend it to anyone.

1948 uni with ri moter $300
8" Yates jointer $200

take it and run.....if was close to me I know I would....I have gotten oak on auctions before that was stored like you described paid next to nothing for it. I probley only threw away about 10%

I got it from the guy on ebay from NY i think it has the 6" inlet. it dosent have the neutral vane like the pentz does but it still does a good job. on the orginal dc i just ran 4" pipe with the...

in regards to the SG contact the the owner theirs a good chance he might be able to custom fit one to your saw.

I bought one of theses and really like it. I first used it as a pull through system then switched it over to a push through system.
Both had there advantages. I have the same dc as you but with a...

+1 on the shark guard i thought about going with a overarm type but went with the shark and love it!!
And whats even better is I keep the guard on the saw 99% of the time compared to 0% before the...

what a steal I have been looking for a jointer and shaper like that for over a year ond no luck,,,,:( I havent even seen a good ww auction in over a year.....

I have a cyclone in front of the filter bags I have I have herd good things about wynn but haven't been able to access there website.

I'm thinking about puting a canister style filter on my grizz dc.
Where would the cheapest place to buy from?

Im wondering you said you have little pressure in the collection bag? when I tried it I have a lot of pressure it didn't break the bag but I was starting to wonder if it was. Does that sound like a...

what /how do you collect the shavings from the cyclone? I saw somewhere someone tied a bag to the cyclone I tried that but couldn't get a good seal and the bag twisted and bunched right at the...

i have one of these and I love it I have mine on a 2 hp grizz

I never used a guard on my saws till I got the shark guard I love it it stays on till I have a cut that it just wont work with...

After over a year of searching I finally snagged one:D.
Just got home with this..... 1950 model with a 3ph bullet motor. for 350.
I hope i did OK... now I need to find A VFD to run it any...

I have a concrete slab floor in the shop and its hard to sweep up.
any recommendations on how to seal it for easier cleaning?
I wont be able to do it all at one time cause I don't have anywhere...

I have a line on a Jet ctas-150 saw. I havent been able to find much info out on this model. if anyone has one or knows anything about this model. Would you recommended buying one? the pic's I...

I am looking for molding knives grizzly planer molder it is similar to the jet model i believe. Not the shop fox molder. I'm looking for some other profiles besides what is listed in the grizzly...

I bought a TS from them bout 10 years ago I never had any problems with them or there shipping.