I have the same problem. So I used 1/2' threaded rod, put a foot on one end and 2 nuts on the other locked together. I use my drill set on low clutch to set them and it all hold fine. I ran the...
Type: Posts; User: Tim Howell; Keyword(s):
I have the same problem. So I used 1/2' threaded rod, put a foot on one end and 2 nuts on the other locked together. I use my drill set on low clutch to set them and it all hold fine. I ran the...
Here in my little town of Williston fl, they do a walk around inspection evey few years, ( amazed me) and do want to look inside any out buildings. So, beware and state what the usage is going to be....
Any lines connected to the air filter/ down pipe/ manifold all the way down to the valve intake? Can the down pipe between the filter and the head be removed? Any small lines connected to the head?...
Keep us posted - I'm interested in the outcome. Got the 1617 myself.
There is a breather somewhere for the crankcase. Your saw dust probly has it clogged up.
Get a 2 stage in what ever you get. Less heat = less water. Cheap single stage compressor will run 90 mph, be noisey and pump out about as much water as it does air, and then burn up. My 2 stage is...
http://www.amazon.com/Freud-D0760X-Diablo-Finish-4-Inch/dp/B001CZEU0S/ref=sr_1_fkmr1_1?ie=UTF8&qid=1331798392&sr=8-1-fkmr1
FreudD0760X Diablo Ultra Finish Saw Blade ATB 7-1/4-Inch by 60t 5/8-Inch...
http://www.jamestowndistributors.com/userportal/show_product.do?pid=1943
Gauge
Check the blade run-out before you kill a bearing in your expensive table saw. Just a safety issue. I bought 5ea 7" from HF - one of the blades had .030 run out, the others ran high but ok and they...
Just a note here. I don’t know from nothing about this, and its really old - but – I caught this part in the first post- Quote “Meguires Swirl Mark Remover”. I too was testing how to polish out some...
You never gave the dimensions of your finishing room in cu ft. Can’t help but think it would make a difference. 6x10x 8 just don’t setup the same as 20x20x12 room.
Scott,
“Never” seemed like the best term when talking to an inexperienced newbie. I too use a Freud LM 74 RO12 rip blade w/40teeth and a 12 degree hook on my radial, but only for ¾” stock as I...
Get yourself the correct blade for cross cutting plywood on your table saw.Take a read here about blades. Many people end up using the wrong blade and get bad cuts and there is a big safety issue...
Be sure you check the heel on the blade. Most people check for square off of one tooth and never think to check if the motor is square on the carriage both horizontal and vertical. You don’t set it...
Anything in this list to help out?
Table 1 – Solvent Evaporation Rates
Dissolving Solvent
Relative Evaporation Rate
I think it's thick too. I would say that the thinners in the can of lacquer have evaporated some and you are spraying a heavier coat of material than you think. The heavy material without sufficiant...
It looks like the total base is all on the same plane. Therefore all the weight is distributed evenly across the bottom. The carpet padding is holding the weight spread out.Therefore it can rock on...
Geez - I haven't heard that term ( S**t Bird) since the early 1950's. It was used by good ole Glenn Edwards in Greensboro NC. Any relation?
Zinseer BullsEye SealCoat is dewaxed. Some people have said the spray cans are dewaxed too, but it does not say either way on their web site. I would like to know if the spray cans are dewaxed or not...
It looks to me like the trim that Jim put around his box was re-sawn on the band-saw. Note, that is where they are stacked, on the band saw.. Re-sawn means you cut a 1x4 in half and make a 1/2" x 4...
I took youradvice with a few mods. Originally I sprayed 2 coats, next day brushed, puttyknife spread as a soup, then a few brush coats. Plenty of dry time between andpin holes over all the pores. So...
I put on a coat at 10 p.m. 70 degrees inside my garage. The low outside last night was 61 degrees. Started sanding it back at 2 p.m next day and coated it at 4 p.m. It was 79 degrees here today....
I used some Polycrylic on a mosiac stepping stone. ( cut glass on concrete stone) I though it would last longer, but the first time it rained on it, the stuff just washed away like wet latex paint....
I am putting Sherwin Williams Fast Dry oil varnish on red oak plywood and hardwood. I am trying to fill the grain with the varnish. I sprayed 2 coats and could see that it was going to take forever,...
Would dropping your router motor on your foot be a steep learning curve or a flat one?