I put a shelix head on my 8 inch Delta joiner and it was one of the best upgrades I made to a shop machine. I bought the head and did not have to tools to add the bearings so I took it too a tool...
Type: Posts; User: Scott Pearson; Keyword(s):
I put a shelix head on my 8 inch Delta joiner and it was one of the best upgrades I made to a shop machine. I bought the head and did not have to tools to add the bearings so I took it too a tool...
Very nice, I really like the hardware that you used and the nails.
I have read that it used in Japanese joinery with a Japanese hammer. The purpose is to compress the tenon to fit the mortise snugly and then allow the tenon to swell from the moisture of the glue...
Really? HSS cutters, that sounds like a horrible idea. Its fine when its two, three or four blades but 25-50 to keep up would be a pain.
Scott
I have a 12" Bosch and I hate it. It is soo big and clunky, ok sure it cuts good and when I bought it I though it was what I needed, however, after having it for 5 years I have decided it's is too...
Yeah, its not the best stuff but still better then what I have seen at Home Depot. The stuff at HD looks more like pringals then plywood.
Scott
Fairly uneventful, I cleaned the shop top to bottom, vacuumed under and around everything. My 10 year old daughter came out right before bed and wanted to work on something but did not have much...
You might look into bandsaw blades further. I believe that the Cabide blades like the Laguna Kerf king do not have any set to them. They would leave a very small kerf and a clean surface.
Scott
It may be a nice vac, but I do not think that they are cheaper then any of the other high end vacs. I went to the site listed and this is the price for the 50 which a a 12 gallon unit. They do have...
Do you know anyone you could borrow from? That would be the cheapest easiest solution.
Other wise you just have to do the math, how much to rent vs how much to buy and if you would ever use it...
What I have done at corners is to clean out the corner well before laying in the stringing. I made mini chisels from eyeglass screw drivers and clean up the corners of the slot. Then you just cut...
There are several drywall products that claim to cut sound transmission by large amounts.
I have never tried any of the products but have been sorely tempted too.
Check out these site:
...
I love it!
There are a number of good options, what is the price point you are looking for? That really defines what options you have, also do you have a router already or would you be adding that as well. ...
I have done something similar. I wanted to make perfectly square holes for ebony pegs. So I bought a couple of motorized mortise chisels thinking I would buy a powered mortiser someday.
It...
I also prefer rasps to a shoulder plane to fine tune tenons, I would also suggest that you look into a float. Like the shinto rasp they have no teeth on the side to mess up the shoulder of the...
Please put me in the drawing.
Thanks'
Scott
That's funny that you mention the warning about the 220 shapton. I have the shaptons 220,1000,4000,8000. I am happy with all of them except the 220, that stone is sooo slow and hardly cuts a thing...
My best suggestion - Buy a second one just like the first
Even the model that you have is more accurate then needed for woodworking the need to go a machinists level is really unneeded. I have...
Count me in, please
I use a sheet of pink foam that I plop on the floor of the shop as a cutting surface, the ply goes down on top of the foam. Then I mark cut lines on each end of the ply and cut using a skil saw with...
I have a Subaru Outback. You would be amazed at what you can strap to the top of that thing. I really do not like doing full sheets of ply but last weekend I brought home about 60 board foot of...
I am in.
Thanks
Scott
Please count me in.
Scott
Please count me in.