Search:

Maybe later today?
519510
Move things around, and chop the 9 mortises in Stile #3...to match Stile #4's 9...and prep things for a glue up?

Then, while Side #1 sits in the clamps for a few...

So far, so good..
Before the Raised Panels could be Dry Fitted up..needed to work on the face that will show, a bit.
.519506
Removed any saw/burn marks...and ridges..and get things nice and...

Ok..back to doing "Spoon feed" for the photos..and see IF things are any better...
Had FAT Rebates..
519504
We have ways..
519505
Run the Craftsman No. 3720 ( Sargent No. 79, Type 2) along...

This one was in use, today..
519487
Fine Tuning rebates...so that the rails will go on better...without binding..

Been complaining about that Photo BS for MONTHS now...nothing was ever fixed...I have to go back and RELOAD each and every photo AGAIN...

And..it is only on THIS site, that this happens...yet..a...

Narrow rails used a simpler mortise..
519482


Have the top and bottom wide rails and 7 narrow rails..

Got about halfway along the Stile,,rotated the stile, and worked on the last...

Had a profile to bandsaw..
519474
So...
519475
We have a foot for the case to stand on.


Cleared off the top of the bench a bit...and set up a Mortise Jig..
519476
Attaches to the bench...

Fire Pit...
519446

First 2 stiles have their grooves done...#3?


There were issues..served me right for working on a Monday..

First..the cutter in the Stanley 45 was acting up...got to...

Just back home..and..
519373
Looking very finely polished and shiny!..
519374
The #39 had issues,,that Eric fixed...as did the #41..
519375
Everything looks and WORKS like new.

Many THANKS,...

Making Crispy Ash Noodles..yum..
519346
about every 3 pass, rub a bit of wax along the groove...tight squeeze..
519347
Had to make sure I was going the right direction, and NOT tear this spot...

During the Lay out..
519341
Decided to see what one side of the chest will look like...8 raised panels...to match the 8 drawers this will have..2" wide rail at the top, and other at the bottom..
...

Since one end looked the best, I started there,
519331
Just hold them square...use one of the 2" wide rails...mark where the tenon meets the groove...square a line across...
519333
then, mark for...

75 minutes in the shop, today...and I am soaked. Will need to look for a Shop Fan...took 36 photos today..had to do some editing...plan was to do a bit of layout on the 4 stiles..then see about...

I also need a rebate all the way around each panel...two saw cuts..one to make a kerf cut..
519294
And the second setting to remove the waste...
519295
So that the panels will sit into the...

The "show face" needs to be beveled on all 4 edges...

Set up the saw with the Zero Clearance Overlay...and tilt the blade to the 15 degree mark on the saw's scale..
519292
Stand a blank straight...

Picked out the narrowest end..set the rip fence to that..
519290
Place the straightest edge against the fence, and run everything through, including the 3 wide boards from the 1 x 6..
519291...

So far, so good...

Had one 1 x 4 x 5' to bring along, and a 1 x 6 x 4' to use...the 1 x 4 was good enough to give me 3 more blanks as is..
519286
But, the 1 x 6?
519287
Will need a bit more...

Going to try something else...had Photo Issues with the last post...had to go back and RELOAD all the photos in the last post...never change anything, before or after....so, will try the spoon fed...

Grooves have been run...over on the tablesaw...as the fence makes using this a bit rough..
519263
Rails are 1-3/8" wide...not enough left to put in a vise, and not hit the fence....was also having...

Ripped the long planks into 4 blanks for the stiles...
519226
The Rails were having issues...
519227
With 18" length looking way too long...and, IF I shortened it down to 15-3/8" long...and...

So..set up a Drafting Table, of sorts...
519210
And, since the edge and the bevel are square to each other...
519211
Made a nice drafting square...the 3-1/2 sections (8) are Raised panels...

...

Must have been a lack of Sharpening Threads going on?

Seen while out and out ...
Aisle/room #5 ( Blacksmith's Tools Stall)
519127
I was just thinking about how much good Irish Whiskey that barrel could hold...
519128
Face vise...
519129
And a...

My little version...
519125
Panel can be any width....one end is clamped into the leg vise...other end clamps to the bench's apron...and a center clamp IF needed...
519126
While sawing dovetails..

Just Ash..same as I always try to get...as I like the way it works, with the tools I have...

By the time we got the Chevy loaded up...there were 18 boards IN the trunk...and my wallet was $30...