Search:

I also need a rebate all the way around each panel...two saw cuts..one to make a kerf cut..
519294
And the second setting to remove the waste...
519295
So that the panels will sit into the...

The "show face" needs to be beveled on all 4 edges...

Set up the saw with the Zero Clearance Overlay...and tilt the blade to the 15 degree mark on the saw's scale..
519292
Stand a blank straight...

Picked out the narrowest end..set the rip fence to that..
519290
Place the straightest edge against the fence, and run everything through, including the 3 wide boards from the 1 x 6..
519291...

So far, so good...

Had one 1 x 4 x 5' to bring along, and a 1 x 6 x 4' to use...the 1 x 4 was good enough to give me 3 more blanks as is..
519286
But, the 1 x 6?
519287
Will need a bit more...

Going to try something else...had Photo Issues with the last post...had to go back and RELOAD all the photos in the last post...never change anything, before or after....so, will try the spoon fed...

Grooves have been run...over on the tablesaw...as the fence makes using this a bit rough..
519263
Rails are 1-3/8" wide...not enough left to put in a vise, and not hit the fence....was also having...

Ripped the long planks into 4 blanks for the stiles...
519226
The Rails were having issues...
519227
With 18" length looking way too long...and, IF I shortened it down to 15-3/8" long...and...

So..set up a Drafting Table, of sorts...
519210
And, since the edge and the bevel are square to each other...
519211
Made a nice drafting square...the 3-1/2 sections (8) are Raised panels...

...

Must have been a lack of Sharpening Threads going on?

Seen while out and out ...
Aisle/room #5 ( Blacksmith's Tools Stall)
519127
I was just thinking about how much good Irish Whiskey that barrel could hold...
519128
Face vise...
519129
And a...

My little version...
519125
Panel can be any width....one end is clamped into the leg vise...other end clamps to the bench's apron...and a center clamp IF needed...
519126
While sawing dovetails..

Just Ash..same as I always try to get...as I like the way it works, with the tools I have...

By the time we got the Chevy loaded up...there were 18 boards IN the trunk...and my wallet was $30...

THIS is what the brand should look like...IF I do it correctly..
519082
Which hangs on the door to the Shop/Laundry Room..
519083
Both of which are in the Basement of the house...

Had to go to...

two burnt fingers later..
519072
Waiting on that Branding iron to fully cool down...before I stash it away..90% of the heat comes right up the handle...

Have a few things to do with a Black...

The Union No. 41 had lost a lot of it's Nickel Plating....so, Mr. Brown will be giving it a brand new Nickel Plate look...

Has been restocked..

Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox...
519069
Eight 1 x 6 x 6'
Five 1 x 4 x 6'

And he threw...

My English No. 4c..
518966
Has been used quite a bit...
518967
Has a groovy sole, too..
518968
A simple little fact: Stanley found out IF a plane was made/assembled in England..they did not...

Hmmm, see how things go, today..
518896
Along with a #12 24 die..there is also a #12 28 die....might be a Stanley size?
518897
Aisle #5 corner...
518898
Stall #4...walk in the front door, hang...

Try again...Project Post, this time around...fingers crossed?
518872
A view of the front..after the Amber Shellac had been rubbed down..
518873
A view of them fancy feet...
518874
A view around...

Hmmmm..can't edit this any more...so...it is what it is...don't feel like doing a repeat of this entry...and take a chance on the same stuff happening again...use your imagination, I guess..

There may be a second plane coming along...Stanley No. 39 3/8"
518756


We'll see...

See how this goes...
518755

A coat of Witch's Brew was mixed first....old stuff was a bit too red...dumped what was left of the Special Walnut into the can..and gave it a good stir..
Coat has been brushed on..and I am allowing...

Laundry Detail. this morning...so..despite it being a Monday....the feet have been leveled...need to unload the washer after a bit...and the Chisel Case...and see about a finish of some sort..
...

Shoptime today? feet installed....fancy feet, at that..
518732
With glue and very small nails..
518733
Letting this sit overnight...

Stay tuned..