Its all good and we all have the right to our opinion. I for one am not anti safety nor anti sawstop more so anti Steve Gass and his partners. I believe the numbers are inflated and are not properly...
Type: Posts; User: Don Wacker; Keyword(s):
Its all good and we all have the right to our opinion. I for one am not anti safety nor anti sawstop more so anti Steve Gass and his partners. I believe the numbers are inflated and are not properly...
What numbers. Where are the posted stats for specific equipment.
I disagree with the suposed frequency of tablesaw blade contact injuries. Ive done this professionaly for 25 years and have never seen, known or even heard mention of a tablesaw blade contact injury....
What makes it Leagues better? How would you compare it to the PM2000 aside from the brake system?
Don
For alot of drilling in long panels not yet assembled. Just drill a 1/4" counter sunk threaded hole in your router plate on the router side and a second one as and edge guide. Install a 1/4 screw in...
I just use one of these mounted in a little piece of angle aluminum clamped to my drill press fence. Drill hole, lift handle slide wood over spring loaded pin drops in hole, drill hole, lift...
I have the expensive Snap-on one, it sucks. The video is horrible, not worth the plastic its made from.
Don
I hate jigs. My shop would be full of jigs if I made a jig for every task that required something special. They hang on the wall a warp so for the most part I dont even bother. For tapers I just grab...
I have a buddy that owns an equipment surplus company. He buys scratch and dent Jet and powermatic by the container full along with oliver and used griz. The parts on what would seem to be the same...
Nema premiums have been around for quite awhile. Other countries did it before the US.
Don
Im a jury member of a similar cooperative. One thing to ask yourself when looking at your finish product. "Is there anything that I could have done a better job on" if yes then you probably should...
I think every saw is a little different and the issue is folks want to group them as just "bandsaw". I dont even use the guides on my saw. I keep them adjusted as far away from the blade as the...
500 chairs is a nice book. I was thrilled to get it for christmas one year.
Don
People our age need to start standing up for what is right. At 50 I couldnt imagine going into the job market. Im on the other side of the fence and did in fact get sued for telling a guy I thought...
If you have an aluminum extension ladder make sure you stick a steel rod or angle iron through the rung. Learned that one the hard way, ruined my ladder the collector was to heavy.
Don
Just make sure you figure out a safe way to get the thing up there they are heavy and awkward not a two man job.
Don
Height with the bin at 4 ft would be higher that this.
http://www.sawmillcreek.org/attachment.php?attachmentid=211083&d=1319491605
IMO yes I swapped mine out the same day I got it and it will most likely stay that way. I dont care about speed and don't do any skip planing.
Don
Every blade will have a different drift.
Don
I have a 3hp it is loud and its mounted outside. I dont know how heavy the two hp is but getting up that high is back breaking. Mine is about 12ft up and that was a job. After hurting my back we...
Probably mis read or misprint. PM manual says 2500 hours. I personally suggest yearly just so you know its full and clean with no metal shavings. More of an inspection rather than an oil change. The...
I was lazy and just bought a rockler dust bucket and hose fitting. Works pretty good.
Don
I wouldnt worry to much about it and just change it once a year or something along those lines. I think if you did the math that would be more than 20000 linear ft of lumber.
Don
I wouldnt under estimate what gallery furniture goes for and people buy it. You do have to be in the right area but its not hard to get well over a grand for a little end table.
Don
Without seeing it its hard to suggest even a pricing strategy. It sound like you want to stick to the gallery market which is very different than retail. Go to galleries in the area and see where...