Search:

Type: Posts; User: Keith Winter; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    2
    Views
    1,262

    Thanks Doug!

    Thanks Doug!
  2. Replies
    2
    Views
    1,262

    Source for white oak?

    Anyone have a source for 1/4" white oak?
  3. For what it's worth I've tossed a number of those...

    For what it's worth I've tossed a number of those green Chinese blowers, utter junk. The $80 harbor freight would be well worth your money to upgrade. With a coupon you can get it even cheaper some...
  4. Looks great Don!

    Looks great Don!
  5. Replies
    18
    Views
    3,672

    Thanks guys, it's about 11 months old.

    Thanks guys, it's about 11 months old.
  6. Replies
    4
    Views
    1,046

    Thanks Ron, Had my guy get on with china last...

    Thanks Ron,

    Had my guy get on with china last night. Took a few hours but they got the rails straight again. Most of time due to the language barrier, but the Thunder people were helpful!
  7. Replies
    18
    Views
    3,672

    Ron what would an ac store be called? Did some...

    Ron what would an ac store be called? Did some googling didn't find much except ac repair technicians like you'd call to your house.
  8. Replies
    18
    Views
    3,672

    Thanks Bill long ways away unfortunately in...

    Thanks Bill long ways away unfortunately in Oklahoma :)
  9. Replies
    18
    Views
    3,672

    Thanks, great suggestions all around. I think I...

    Thanks, great suggestions all around. I think I will see if there is an ac shop I can take it to per Rons suggestion.
  10. Replies
    4
    Views
    1,046

    Aligning rails

    Seems today is not my day....

    Employee just ran the chinese laser into some wood knocking the middle rail out of alignment. It's a thunder laser, similar case to the gweikes I believe. The middle...
  11. Replies
    18
    Views
    3,672

    Ok so I don't know a lot about compressors and...

    Ok so I don't know a lot about compressors and such but here goes ;)

    On the left side the black thing I'm pointing to that appears to be the compressor yes? It is vibrating so it is running, it...
  12. Replies
    18
    Views
    3,672

    My other chiller the same room is working fine,...

    My other chiller the same room is working fine, was working fine for 6 months until today. The CW series chillers are adjustable from 15c-30c. It's about 65 degrees in the room right now (18.3 C),...
  13. Replies
    18
    Views
    3,672

    Chiller not working

    My chiller is behaving oddly. It's only 60 degrees farenheit in the room but it's having trouble chilling the water down to 19 degrees Celsius even with the laser not running for many minutes at a...
  14. Thread: Vice

    by Keith Winter
    Replies
    12
    Views
    2,602

    Thanks for that photo Kev, I can see how that...

    Thanks for that photo Kev, I can see how that would be handy. Photo is a thousand words!
  15. Replies
    7
    Views
    3,606

    Thanks everyone for the replies. Haven't solved...

    Thanks everyone for the replies. Haven't solved the mystery yet. Emailed china waiting to hear a reply.
  16. Replies
    7
    Views
    3,606

    Auto Focus not working Chinese Laser

    I have a couple chinese lasers using RDworks as the software. All the sudden autofocus stopped working on both of them and the tip just runs into the substrate if you try to auto focus and doesn't...
  17. Replies
    12
    Views
    3,038

    Great ideas thank you!

    Great ideas thank you!
  18. Replies
    12
    Views
    3,038

    Not sure all the trotecs do it. I wonder if that...

    Not sure all the trotecs do it. I wonder if that can be disabled? Would fix the problem...
  19. Replies
    12
    Views
    3,038

    No it's screwed on from below. You'd have to get...

    No it's screwed on from below. You'd have to get under the closed cabinet to access from below. You can disassemble the screws holding the bed to access it but that takes about 20 minutes to do and...
  20. Replies
    12
    Views
    3,038

    What happens, not often but time to time, is the...

    What happens, not often but time to time, is the operator leaves what he was working on the night before on the bed. When he turns it on in the morning it automatically lowers. When it automatically...
  21. Replies
    12
    Views
    3,038

    Hi Jit, You're on the right track there but...

    Hi Jit,

    You're on the right track there but the bed actually goes lower than the front lip. So if something falls behind the laser. You shut off the laser and turn it back on the next morning it...
  22. Replies
    12
    Views
    3,038

    Items falling off back of bed

    From time to time small objects fall off the back of the Trotec Speedy 400 bed, there is a gap behind the table that allows this. Problem is if something falls off the back while the bed is up it can...
  23. Replies
    11
    Views
    2,431

    Impressive job lining that up!

    Impressive job lining that up!
  24. Replies
    9
    Views
    2,163

    1 in this situation. You are simply resizing the...

    1 in this situation. You are simply resizing the logo it sounds like. All the main setup work is done on the 1st. Now if they are two different logos then two setups would apply.
  25. Replies
    23
    Views
    12,296

    There are "redsail" knock offs. Meaning others...

    There are "redsail" knock offs. Meaning others that use the same case that are not redsail. Did you buy it from eBay, if so which company did you buy it from?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4