I am glad you enjoyed it. It was fun putting that together
Type: Posts; User: Howard Boehm; Keyword(s):
I am glad you enjoyed it. It was fun putting that together
459527
I have put together a complete video guide and a cheat sheet for doing Vcarve inlays. This take all the guess work out of doing inlays. https://youtu.be/v7KMRombA1Q
I think you will...
Its about 1/2 inch higher than it was with the factory base.
What do you mean when you say make sure the remote power is off
I took up the whole wall but with all the deawers I have way more room and extra storage that I have yet to fill
https://youtu.be/K_csiE4eBOc
My wife enjoys it as much as I do. I can't tell you how many times she yells stop and points out the error I am about to make. And dammit she is always right.
339402
My wife and I built our home bar. I put together a video of the building.
https://youtu.be/-KiP0LL7gWQ
As you can see I even had room for the lumber racks above the station. As a 60 plasma tv to watch the youtube videos. Neighbor was throwing it out as it had 2 vertical lines going down the screen 1...
OK, at least I know I am not crazy. I was thinking I see it then I don't. Thanks for the clarification.
I have a post that I wanted to add some additional photos to. I don't see any edit button. When I replied to a question I noticed on the reply at the bottom there was an edit button, but now its...
I must say I felt the same way, I didn't think I had the room. But everything on the wall is now in drawers, Half the drawers are still empty. The old shop vac fits underneath as well as one of the...
I got the tubing at Industrial Metal Supply, 1 inch Square and I believe it was 11 gauge. I had them cut the length I needed. Al I had to do was drill the holes. I was going to make a whole new base...
I got them at Linco casters in San Diego. here is a link to the type of caster I used. They have dual wheels which are great on garage floors when you go over a joint in the concrete. Smooth as silk...
I got so tired of the mobile base that was made for the unisaw with the 55" extension that I was going to build a complete new one. As I was drawing it I came up with a solution that was ten time...
I built it in 3 weeks but I procrastinated for about two years.
How much room do you have in that workshop. That's what I need, space.
Great bench.
Do you have photos or video showing how you did the glue up
The tape measures seem to go off on their own. At one point I had an even 10 don't know where those last few went.
I got the initial Plans From Jay Bates. He shows some of the best videos I've Seen. Here is the link to his page for the plans...
327514
http://youtu.be/K_csiE4eBOc
Finally built my miter Saw Station, It took on a life of its own as it kept growing and growing. Hope you enjoy the video
Howard
8 Inch Rounded Fluted Columns made from flat stock on Legacy Ornamental Mill
http://youtu.be/1ue4qfLNlEo
This is my second table for the outside dining area.
271204
African Mahogany Top
271205
Cut my 6x6 and did a lap joint on the cross members
271206
Cut up another of my wife's cutting boards...
I just got mine today. Only complaint the manual's print is to small. Setup was very non existent once I figured out how to release the lower guides. I know. read the manual first. I made some cuts...
it is a Legacy Ornamental Mill. I do the rounded fluted columns, 3 twist spirial hollow in the center etc.
I used system 3 marine varnish. I used satin and its perfect. The high gloss you see in the picture was after I just put a fresh coat on and it didnt dry yet. It has a very low sheen.