I am old but not yet blind so why can't I find the For Sale/Classified section
Type: Posts; User: Jerry Bittner; Keyword(s):
I am old but not yet blind so why can't I find the For Sale/Classified section
Bought a replacement conveyor belt for my Performax and cannot get the belt to track true. It always wants to drift toward the motor side. I even took all the tension out of the adjustment screws...
That simple huh? Thanks
This is a photoof the blum hinge showing the cover.
How to remove is the question.
I'm almost embarrssed to ask this but here oges. I'm replacing many cabinet doors and they have the european hinges.
The hinge on the door side has a cover that hides the screws, Okay here it...
Thanks much appreciated
I'm building cabinet doors. The frame includes a groove to allow for fitting in a wainscot panel.
To prevent rattling, I have used foam backed adhesive tape 1/4i inch wide, and about 1/8 inch...
One side is out of the track/channel. I can move it up and down to a limited degree but it does not roll easy.
My wife recently\ acquired a roll top desk.
The roll top is hung up -- the slats do not fit into the groove on one side.
Try as I can, I can not slide the roll top over to engage the problem...
Having a problem with a lacquer finish. I first sprayed the piece with Lacquer Sanding Sealer (Deft) and then applied lacquer. Everything fine thus far. Ran out of the Deft lacquer and bought some...
Thanks for the information. I went to the Butcher Block site and that sure is some impressive work.
I did my table as I recall by gluing about eight pieces, eight more and so on and then glued the...
The missus wants new counter tops and she is pushing for the design I used (copied) to make end grain cutting boards and to make a small end table -- pic attached.
The counter top has to be 30...
Thanks Jim, I'll give him a call. Took it apart last night and the switches seem to work okay. No current flowing through them until actually switched on.
I have a shop Fox remote control for my 220 voltdust collector. Recently encountered this problem. One of theremote transmitters would start up the DC but as soon as I released the switch,it would...
Thanks everyone. I found a site that all you do is plug in the particulars and it gives you the fpm-- mine ended up at 2800
Have to get a new motor for my ancient Delta 12" bandsaw. The pulley on the bandsaw is 6' diameter. I realize the diameter of the new motor pulley will have to be sized to relate to the bandsaw
so...
I have the Compucarve -- one of the first an A model. Since been upgraded with the Rock chuck, rubber belts, etc. Extended the original maintenance agreement for one more year and notice that I am...
I have the Compucarve -- one of the first an A model. Since been upgraded with the Rock chuck, rubber belts, etc. Extended the original maintenance agreement for one more year and notice that I...
Picked up one of these sanders and have a question about the fine tuning adjustment. I have the spring for the adjustment knob but no knob and washers. I ordered the knob but the washers are not in...
I've acquired from Adams Wood the four rice posts I plan to use for the construction of my daughter's king size bed. The posts are made in three sections, the bottom square is no problem for the...
I have the Sears equivalent of the BT3100 which was my first table saw and I continue to use it but primarily resrved for cutting dados.
Recently I noticed that even though I have the height...
I'm looking for a source for plans for a king size bed. I'd like to be able to send pictures of various styles to my daughter for her choosing -- its going to be a wedding present for her.
So...
Okay, I've got a few roundover bits. Question is how to determine the radius since they do not have any markings.
That is, for any individual bit.
The "standard" size (Hme Depot, Sam's etc) -- 5000 KV -- should do fine. That's what I have and they normally come with a loading list advisng you of what the typically load is for various...
I need some ideas about how to build a crib with a sleigh type top to the two ends -- see attached picture.
I built a jewelry box that has similar curved sides that were achieved by running the...