You Should Specify The Maker Of Your Compressor Here As Well
Type: Posts; User: Steve Flavin001; Keyword(s):
You Should Specify The Maker Of Your Compressor Here As Well
See attached plan from Woodcraft and Wood magazine
http://www.sanborncompressors.com/, "Technical support available" 757-410-2879 or -7822?
One week old? Am I missing something?
tasks such as 1/8 and 3/16 roundover of stock to illustrate.... to avoid constant changing of bits, each dedicated to that function.
One dedicated to router table because changing back and forth...
joint as mentioned, but if the glue is on the surface at all stain will not penetrate the glue and your finish, particularly if relatively dark will have blond spots.
be wonderful also - their floor space and cost to me were not justified. Unlike the comment that flipping to the second side was a hassle, I have no problem - it is always set for that and 20" is...
the DW! Check the specs of both and particularly the knives - the speed of cutting RPM, feet/minute and the thickness of the knives.
The planer is rated at down to 1/8" - critical issue that I see...
but what is the difference between attaching an image (this thread) using the paper clip, and uploading a JPEG file using the Manage Attachments window within the Attach files box border below - same...
screws that show in the photographs?? :confused: There are 8 set screws, in addition to 4 or 6 larger ones from below that can be used as Glenn points out in his note also. Am I missing something?
it to you unless you have a business license and appropriate spray booth facilities in order to comply with air quality (VOC) regulations - state and/or federal as might be the case.
At least that...
representative hinge shown, select specific model for your corresponding door structure.
Also, BB is pretty expensive stuff for cabinet cases (realizing it is on hand), in some minds, overkill;...
jig - ideal for this. I made the Wood magazine three stacking tables identical in concept, using it. Can also use screw in top covered by wood plug re lifting concerns expressed.:o
point it out. I BOUGHT a HF-TYPE joiner once, sold through a major retailer no less and found out the the precision is not all as simple as Al underestimates, with all due respect. The additional...
satisfactorily operate is marked prominently on the box of nails.
While substantially interchangeable there are exceptions - particularly in the 15-16 gauge nails. Do not assume all nails of a...
Chamfer Router Bits re 49404 :eek:
"2 Flute
Chamfer or bevel edges for decorative effect or to form edge miter joints. Produce crisp, uniform edges at accurate angles to make 4-, 6-, 8-, 12-,...
I believe the 30" "standard" is more materials and construction convention then any code - 30" gives you 3 pieces from an 8' sheet of material while two nominal 36" (e.g. 30 - 36) simply leave you...
to looking this up, I stumbled across a discussion of some local codes in one state that went at exhaustive length (ad nauseum) in discussing kid's requirements, particularly in the event the...
curiosity made me start to look this up. Local building codes and federal reg's are intertwined in long histories of building on one another as precedent in the rule making process (interesting...
locks tend to be pretty standard in any decent hardware store - my photo shows lumber rack on wall in back corner like yours. 5" castors seem to be minimum acceptable for stability.
end maintains the necessary rigidity. One end is adequate and necessary to view what is there but more so to avoid lifting sheets - particularly wide ones.
As is probably apparent, my vertical...
my cart. The 5" rubber castors on slight outriggers seem to handle topple effect quite well. It handles 8' sheets but overhead clearance can be a nuisance in my area; my main situation is lots of...
also found the price was as varied as the OEM one-factory label, for sale based on the mood and disposition of the sales rep. There must be a substantial room for markup in these as well, sold from...
familiar to you, Milton is the de facto manuf for such fittings. Their 76X V-style or 72X series are what you want. The 76X connectors are 1/64 larger in. diameter required for HVLP guns because of...
See Wes Billups this forum, 6-19-2008, 11:20am sawmillcreek.org/showthread.php?p=875566#poststop
from glowing in your compliment, but this jig, made in some Chinese factory (thus the name universal, we think :D ) appears identically except for paint color and label in everything from Delta to...