I'm More Of A Reader Than Poster; However, The One You Are Talking About Has Been Extremely Busy Today With Nothing Positive To Add. I Agree Fully.
Type: Posts; User: RANDY PAULK; Keyword(s):
I'm More Of A Reader Than Poster; However, The One You Are Talking About Has Been Extremely Busy Today With Nothing Positive To Add. I Agree Fully.
Score With Sharp Knife Before Cutting With Your Saw
Byron, It Is Probably 45 Or 52 Degrees Depending On The Back Cut Of The Moulding. I Usually Cut 52 Degee Blocks When Installing Wide Crown To Keep It Aligned With The Wall Correctly. Been Awhile...
Byron, When I Make Crown Moulding, I Cut The Back Sides 38 Degrees Top & 52 Degrees At Bottom For Better Width On The Wall Or Both On A 45 Degree Angle. Hope This Helps.
Jim, I had a similar problem with mine a few months back. Like yours, mine had always been difficult, since I purchased it five or six years ago. I finally removed the top and had to align or...
Jerry
Shoe Moulding Would Be Just As Appropriate. It Is Only 1/2' X 3/4' And Can Easily Be Made With A Roundover Bit. The Moulding Doesn't Have To Be 3/4 By 3/4, Unless That Is Specifically What...
Paul,
It Depends On The Type Of Wood Used. You Can't Do It With Red Oak, Hickory, Or Other Hard Woods. You Get Too Much Waste From Tear Out. Or At Least I Have Not Been Able To Do So Without An...
Paul,
The Multipass Rollers Have Stronger Spring Pressure Which Allows You To Make Lighter Cuts With As Many Passes As Needed For Difficult Grained Or Harder Wood. If You Try It With The Normal...
I have the older model william and hussey moulder, which I upgraded with the vari-feed motor and multi-pass rollers. Made the machine much better to use; Especially with harder woods, since you can...
They are for 20 amp. i have them throughout my shop.
Brad,
it can be purchased in 1 gallon cans from highland woodworking. highland woodworking.com. 800-241-6748
Ted Thanks
I'll See In The Morning If I Can Find The Problem. I'm Hoping I Don't Have To Dismantle To Find The Problem. Major Problem Is I Have Excalibur Sliding Table Attached To The Motor Side...
Ted
I Appreciate The Advice. I'll Look And See. I Also Noticed A Grease Fitting Under The Trunion That Is Visible When You Stick Your Head Under The Cleanout Area. It Possibly Lubricates The...
Height Adjustment Frozen Up / Seized Up And I Can't Raise Or Lower Blade. Saw Approximately Five Years Old With Light Hobby Use. Has Always Been Somewhat Hard To Turn. Where Do I Look To Find The...
Dennis, I Used Drywall Screws. I Just Start The Screws And Then Cut Them Off With Side Cutters If They Are Too Long.
Dennis, I Just Installed Three. You Install The Drywall, Then The Door And Then The Final Trim.
chris
I am more of a lurker, however my wife and I are doing the same type of project. we purchased 40 acres of land for our final home. We built my shop a 60x75 x 12 steel building first. It...
There Is A Company Out Of California That Sells The Glue In 16 Oz Bottles. They Supply You With Small Bottles For Use For Free. They Send You The Glue After A Telephone Call To Their 800 Number. ...
I Live In The Panhandle, Pensacola Area, Water Front Lots On The Gulf Are Through The Roof Unless You Go Somewhere East Of Panama City. Even Bay Front Or River Front Lots Are Geeting Espensive And...
greg, as you cut crown molding, you cut back on an angle. initially you are cuting almost a 45 degree angle under the ege of the molding, which allows the coped edge to fit tight.
I Have The Pm66 With The Excaliber Sliding Table. I Have Been Using It Two Years And Could Not Be Happier. I Must Admit Though That I Also Have An Older Saw With The Longer Rails And A Right Hand...
The Angle Will Still Be 45 Degrees. You Don't Have To Worry About The Taper.
Sam, That Is A Good Video And Will Help You Better Understand Woodturning; However, You Would Be Wise To Get Hands On Experience With Someone Before Trying To Use Your Lathe. I've Seen Too Many...
Sam, I Am Not One To Reply To Many Posts, I Am Mostly A Lurker; However, I Know A Little About This Subject And Would Suggest You Contact Your Local Chapter Of Wood Turners, Tidewater Turners Of...